Model #11064202200 KENMORE Residential Dryer

  • Cabinet
    3 Results
  • Top And Console
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Why does my Kenmore dryer only buzz when I push the push-to-start button?

A:

Thank you for your question.  I am sorry you are having a problem with your Kenmore 110.64202200 Electric Dryer.   From the description you give I suspect the motor but there is something you should try first.   My first suggestion would be to get an extra hand and hold the door switch in.  With one hand push the start button.  With the third hand give the drum a push while the start button is being held in.  If the dryer starts when given a push the problem is likely the motor or voltage.  If a meter is available and you feel comfortable checking voltage check across the blue and black wire while the start button is pressed.  I hope this helps.  You can reply with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
October 20, 2013
Q:

dryer squeaks on start-up, noise stops after a minute or so

A:

Thank you for your question.  I am sorry you are having a problem with your Kenmore 110.64202200 Electric Dryer. From the description of the problem I suspect the squeak you hear is from the idler pully.  The drum rollers usually cause a thumping noise.  The belt is routed around the idler pully.   A good prevenative maintenance project would be to replace both the Belt and Idler Pulley at the same time.  The idler pulley you get will be a new and improved version and may not look like the one on the dryer now.  The image below will show how to raise the top and remove ther front panel to access the belt and idler pulley.  You can reply below with any additional details or questions. 

Read More
Fred M -
Sears Technician
August 17, 2013
Q:

dryer model #110.64202200 is not heating...

A:

It's such an inconvenience not to have your electric dryer working correctly. I found a similar link on the Manage My Life website, which you may find helpful towards your issue. While your waiting for a detailed reply from an expert, I have provided the link below.

Read More
Yadira -
August 07, 2012
A:

I recommend that you check the house circuit breakers first. This brief video shows how to check that issue: Video: Dryer Won't Heat . If the house circuit breakers for the dryer outlet are okay, I recommend that you check the voltage at that outlet as shown in this video: Video: Perform a Voltage Check on a 240 Volt Outlet . NOTE: Follow the safety guidelines in that video when checking that outlet voltage. If you are not completely confident in your technical ability to check that outlet voltage, then I recommend that you have an electrician or service technician check that issue . If you do not measure the correct voltage at the outlet, then I recommend that you have an electrician repair that electrical outlet.

If the outlet is okay, then you could have a problem with one of the components in that heating circuit. The first image below shows the wiring diagram for your dryer with the heating circuit traced in red and green. You indicated that you already replaced the thermostat and the element. I assume that you replaced the operating thermostat on the blower housing. You can unplug the dryer and check the thermal cut-off fuse and high-limit thermostat for continuity using a volt/ohm meter. The second image below show the location of those components on the back of the dryer. Here is a brief video that shows how to test a fuse or component for continuity. If the thermal cut-off fuse is blown, then you will need to replace that high-limit thermostat at the same time that you replace the thermal cut-off fuse. That high-limit thermostat is assumed to be defective since it did not prevent the thermal cut-off fuse from blowing.

You can order parts from this page: Kenmore Dryer Model 110.64202200 Parts . Be sure that you unplug the dryer before accessing and replacing internal components.

If the thermal cut-off fuse and the high limit thermostat are both okay, then you could have a bad timer, a failed motor centrifugal switch or a wiring failure in that circuit traced in the first image.

I hope that this information helps. If you need further assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 09, 2012
See more answers

Top Parts