Model #11064082201 KENMORE Residential Dryer

  • Console Panel
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Dryer Top
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Control panel won't work 11064082201 Kenmore Electric dryer

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your dryer. Upon researching model 11064082201; it sounds like the electronic control board may need to be replaced. The electronic control board governs the functions of the dryer so when it fails it can cause the unit to become unresponsive. I have posted a link of the control board to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
May 19, 2015
Q:

DRYER DOESN'T TURN ON

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Jackie S -
October 31, 2011
A:

Thank you for your question and I understand your concern.

The thermistor part #8577274 should have a resistance measurement of 11.9K Ohms at room temperature of 70 degrees and a resistance measurement of 9.2K Ohms at room temperature of 80 degrees. Based on your findings of 9K Ohms; the thermistor is Okay.

I assume the dryer will power up and program but it won't start. There is a thermal fuse (part #3392519) located on the blower wheel housing that if it fails (opens) it will break the voltage circuit to the motor and prevent the motor from starting. If the belt is off or broken; the belt switch will also break the voltage circuit to the motor. The control board can also fail and prevent the dryer from starting too. After start is pushed, the voltage to the motor can be checked at the control board across P1-4 and P1-3 and then across P1-4 and P1-2.

I added a wiring diagram in the image below that should be helpful.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 01, 2011
A:

I have the same dryer but my led panel doesn't turn on. i took it apart and dusted everything off, but i put it back together and it will turn on but if i turn it off it won't come back on. i have smelled a funky smell when it turns on. any idea will help

Read More
Marlon -
December 29, 2014
See more answers
Q:

Kenmore Sensor Smart Electric Dryer, Model No 110.64082201. The control panel is malfunctioning. When setting temperature and press start is beeps three times

A:

Having a dryer that is not starting properly can be a hassle and keep you from drying your freshly washed clothes. While you are waiting on an expert to answer your question, I found a great link in the managemylife.com website on your problem with your Dryer. Click here. Hope this helps!

Read More
Dezeray S -
July 17, 2013
A:

Thank you for your question and I understand your concern.

It could be one of two things, it could have a faulty door switch and the control does not detect the door being shut or it shorted touch panel.

You can test the door switch operation after placing the dryer in a diagnostic test mode.

 Activating the Diagnostic Test Mode:

 

  1. Unit must be in Standby (unit plugged in, display off).
  2. Alternately press the More Time ∧, Less Time ∨ touchpads two times. All LED’s should light and the display should show 88. If any of these initial conditions are not satisfied, the control will not enter the test mode.

 

When the control is in the Diagnostic Test mode, every input change of state will result in a beep, including the Door Switch, and the Moisture Sensor (short/open Sensor will result in a beep).

NOTE: A moistened finger or damp cloth may also be used to place across the two metal moisture sensor strips located below the lint filter intake grill.

If the control does not make a beep when the door is opened and closed after entering the diagnostic mode then you will need to check the door switch operation with an Ohm meter. 

You will need to access the door switch or it can be tested from the control board. To test the door switch operation from the control board, disconnect the P1 connector from the control board. Place one Ohm meter lead on the P1-2 (white) and the other Ohm meter lead on P1-3 (blue) and with the door shut, the Ohm meter should measure continuity. If it doesn't, replace the door switch, if it does measure continuity, the touch panel is likely faulty or possibly the control board. To access the control board, the control panel must be placed in the service position. Remove the screws at the back of the two control panel endcaps. Slide the control panel towards the front and lift it up and hinge over the rear panel.

NOTE: Disconnect the dryer from the power source before accessing the control board inside the control panel. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
July 18, 2013
See more answers

Top Parts