Model #11063032101 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

i can't get the back off of my dryer. it seems to be welded or glued on. i need to replace the heating element. model #110.63032101 11063032101 Kenmore Electric dryer

A:

The back doesn't come off. The front does. You need part # 3387747 which is the heating element for this dryer. You then should be able to remove the bottom panel below the door to access the internals. Make sure the dryer is unplugged first! Also, how are you sure you need a heating element? There is also a thermostat and a control board that could be causing your dryer to not heat up. You can see an exploded diagram of your dryer's cabinet to see how it comes apart by going here: http://www.searspartsdirect.com/kenmore-dryer-parts/model-11063032101/0582/0151200/P0203281/00002.html best of luck.

Read More
Christopher -
August 29, 2015
Q:

how do i replacemy heating element on my kenmore elite dryer mod.#11063032101

A:

I can fully understand your need for proper instruction on replacing your heating element for your dryer.  I've located that provides a couple of videos that are model specific to your unit.  Click here to view the link.  Though this link discusses a different model number,
the mechanics are likely going to be very similar. Keep in mind that an expert will be
responding within the next two business days if not sooner and will likely offer you more information and
instruction. I hope this information will be helpful and have a nice day.

Read More
Henry -
June 21, 2013
A:

Thank you for contacting ManageMyLife.com regarding replacing the heating element on your Kenmore electric dryer. I see Henry provided you with an excellent link to a video that will instruct you on how to replace the heating element on your model. I also provided you with a link to the video.

The heating element is part number 3387747 and can be purchased from Sears PartsDirect. If you do not feel comfortable repairing this issue yourself, service can be scheduled at the following link: Sears Home Services.

I really hope this information helps you today. Thank you for using ManageMyLife.com.

Read More
Korinna S -
Sears Technician
June 21, 2013
A:

I can't get the back off of my dryer. It seems to be welded or glued on. I need to replace the heating element. 110.63032101 model #

Read More
Herb -
August 29, 2015
See more answers
Q:

Dryer won't run unless start button is held and won't stay running 11063032101 Kenmore Electric dryer

A:

Also, the thermal fuse has continuity. I have also checked the door switch (the light would go on/off based on the door being opened/closed) I also checked wiring harness for the door switch. When testing the two outer pins there was continuity.

Read More
jjp_jeff -
October 15, 2014
A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dryer and I do understand your frustration. Glad to help out. I'm looking at your model number and the dryer starting without having to push the start button indicates that you either have a shorted start switch or that the motor relay is stuck closed. If you unplug the dryer and access the start switch in the console, you can check it for continuity when it is not pressed. To access the console, pull the plastic end caps off of each side of the console. Remove the hidden screws that you will find under the endcap of each side that secures the console to the top dryer panel. Pull the console slightly forward and then hinge it up and back over the back panel into the service position. Pull one wire off of the start switch (with the dryer unplugged) and check for continuity across the leads of the switch with a volt/ohm meter. You should read infinite resistance (open) when the button is not pressed. You should measure continuity (near zero ohms of resistance with the button pushed. If it has continuity whether it is pressed or not, then the start switch will need to be replaced. 


 If the start switch is okay, then you can check the motor relay in a similar manner. Pull one blue wire off of the motor relay and check the continuity across the leads that the blue wires attach to. If you find continuity through these leads, then the motor relay is stuck closed and will need to be replaced. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others. 

Read More
Sherman_G_Wallace -
Sears Technician
October 16, 2014
See more answers

Top Parts