Model #11062994102 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Newe electronic control board for electric dryer does not seem to work

A:

I understand that when dealing with older appliances it can sometimes be cheaper in the long run to just replace the entire appliance. Hopefully, with the help from Manage My Life you will be able to save your trusted dryer. I have attached in a link below the possible causes of your dryer not heating. I hope this link is helpful for you while you wait on your response from an expert. Have a great day!

Read More
Alina -
November 09, 2012
A:

You could have a problem with the voltage supply to the dryer. The dryer will run if only 120 volts of power is supplied to it. If the second leg of 120 volt power (traced in dark red on the wiring diagram below) is missing, then the dryer will not heat. If you have a volt/ohm meter, you can check that voltage at the dryer outlet as shown in this video: Video: Perform a Voltage Check on a 240 Volt Outlet .

If that voltage is okay, then you could have a bad heater relay. You can unplug the dryer and connect the red wires going to that relay to bypass it for a brief test. Tape the wires to make sure that they do not short out to the metal dryer cabinet. Start the dryer and see if it heats with that relay bypassed. If it does, then you will need to replace that heater relay (part 3405281). Be sure that you unplug the dryer and restore the original wiring configuration following that brief test. You can order parts from this page: Kenmore Dryer Model 110.62994102 Parts . Be sure that you unplug the dryer before accessing internal components and replacing parts.

If the dryer does not heat after bypassing that heater relay, then you could have a blown thermal cut-off fuse, a bad high limit thermostat or a failed heating element in the dryer. If you need help, accessing and checking those components, reply with additional details and we will assist you further.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Note: You may be able to return that control board if it was not needed.

Read More
Lyle W -
Sears Technician
November 10, 2012
See more answers
Q:

Dryer will not heat

A:

I understand how disappointing it can be with the dryer not heating. I have done some research on the Manage My Life website and have located similar information towards your issue. While you are waiting for a detailed reply from an expert I have provided the links below. Hope this helps!

Read More
Priscilla V -
April 29, 2012
A:

If replacing the element didn't help then the next likely suspect would be the heater relay. The heater relay is located in the console. There is something I suggest you try next. I'd suggest you raise the console to access the heater relay. The image below will help with this. In the console there are a heating relay and a motor relay. The dryer runs so we know the motor relay is okay. The trick to try next is while the dryer is unplugged swap the relays. The motor relay and heater relay are the same part. If you swap the relays and the dryer no longer continues to run when the start button is released then that relay if bad. If you swap relays and the dryer still runs then the original heater relay is okay and the problem will be one of the thermostats or even the control board. The image below shows how to raise the console. Remember to unplug the dryer first. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
April 29, 2012
See more answers
Q:

What would cause my Kenmore dryer model 110.62994102 to stop in the cycle and give 3 beeps?

A:


The three beep signal is telling you that the thermistor in your dryer is open. The thermistor is a variable resister that increases resistance with heat. It is how the dryer senses the temperature in the tub and knows when to cycle the heater off and on.

If the temperature in the room where your dryer is located drops to 40 degrees the thermistor will read open. We have this problem often if the dryer is located in a garage. Can you trace your problems to happening on cold days? If your dryer is located inside the house there could be a problem with the flapper in your vent hood letting cold air in.

If weather is not causing your problem the thermistor should be replaced.

Read More
expert -
Sears Technician
January 11, 2008

Top Parts