Model #11062924100 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

my kenmore series 90 does not dry properly, it takes a long time to dry. The dryer is heating some, but not enough 11062924100

A:

Thank you choosing Sears for your repair needs.  If the dryer time is longer than normal or expected, please check your dryer vent for a clog.  If you check your laundry and the clothes are warm and moist, there is blockage either in the hose, the vent where the warm moist air exits, or if you live in an apartment, possibly the passage up through the roof.  The first check is to remove the hose from the back of the dryer to check for lint build up in the back by the vent hose.  This should help resolve your drying time issue and as always thank you for choosing Sears.

Read More
John7905 -
Sears Technician
August 07, 2015
Q:

i am looking for the installation instructions if i order a heating element for a kenmore 90 series #110.62924100 electric dryer.

A:

Good morning... I can fully understand your need for proper instruction. I did locate a link that will discuss this situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you change out your heating element and have a nice day.

Read More
Henry -
February 15, 2013
A:

Hi,

Thanks for contacting ManageMyLife.  I understand how frustrating it is having trouble with your appliance not working.

The element on the dryer replacement will require some disassembly.  One way I use is the fast way that is to take the kick panel off after disconnection the dryer from the wall outlet.  Once the panel is off I pull the harness off the burn tube and remove the bolt holding the tube to the cabinet and just slide the heater out.  Remember the order or mark with tape the wires front to rear and go for it.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
February 15, 2013
See more answers
Q:

Electric Kenmore Dryer

A:

It can be very upsetting when your electric dryer will not start at all. I did some research and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
October 25, 2012
A:

Thank you for your question and I understand your concern.

There are several possible failures preventing your dryer from starting. Since you heard the sudden pinging noise, the drive belt could have broke or has come of the motor pulley. This dryer has a broken belt switch which will trip open if the belt breaks or comes off which will break the electrical circuit to the motor and it will not start.

If the thermal fuse fails, it will also break the voltage supply to the motor and it will not start. If the door switch is faulty or if the motor is bad, it will not start.

The first thing I would check is to see if the belt has broken or has come off the motor pulley. Your dryer has a lower access panel below the door which can be taken off to inspect the drive belt. The thermal fuse can also be accessed and checked at this time. The thermal fuse is located on the blower housing duct. The thermal fuse can be disconnected and tested for continuity with an Ohm meter. See images below for instructions. I also added an image of the wiring diagram and I traced the start circuit in Red and Green. NOTE: Disconnect the power cord from the power source before servicing.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
October 26, 2012
See more answers

Top Parts