Model #11062902100 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore electric dryer

A:

A dryer is an appliance we depend on so much, when there's laundry to be done.  While you are waiting for an expert to respond I was able to locate some great information that could possibly assist you with your issue.  I have added the link.  Click here to view.  Hope this helps!  

Read More
Yadira B -
July 07, 2013
A:

Thank you for choosing ManageMyLife.com. I understand how important it is to have a properly working dryer. Based on the symptoms you've provided, there are a few things that could cause this issue. Since you tested the door already, you may have a non-working switch. When you push the start switch and nothing happens and you do not hear the humming of the motor, this could be the cause.
I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.
Push-to-Start Switch for Kenmore Dryer Model # 11062902100
If the motor isn't humming at all, you may want to check if the dryer motor is getting proper power voltage. If it is getting proper voltage, you may want to test the motor to see if it needs replacing.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Unplug the dryer power cord from the electrical outlet.

2. Open the cover for the lint screen on the top of the appliance. Slide out the screen and remove the screws underneath with a screwdriver. If the screen on your model is built into the door portal, skip this step.

3. Use a flat-head screwdriver to raise the top corners of the appliance between the top and the front.

4. Grab the clip in each corner under the top, at the front, with pliers. Squeeze the clips to remove them. This releases the top from the front panel.

5. Extract the screws on the sides of the front panel and the bottom panel immediately below it.

6. Pull off the front panel. Unplug the door switch from the wires on the back of the panel. Push down on the bottom panel, and tilt upward from the bottom edge to remove this part. Now you can see the dryer motor on the right, at the bottom.

7. Pull the two wires off the motor terminals one at a time, making a note of where each wire connects. Each wire has a Y-shaped clip on the end that pulls off the motor.

8. Hold the two test rods on the multimeter to the motor terminals. Set the meter to "X1," which is the test for continuity. If the motor does not produce a reading or the meter display numbers flash endlessly, the dryer motor is burned out and must be replaced.

I have included a link to our PartsDirect page where you can purchase the part you need to complete your motor repair. Just click the blue link below to be taken to the page.
Drive Motor Assembly for Kenmore Dryer Model # 11062902100
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If you would like more assistance, reply to this thread, please include more symptoms if possible and I will be glad to assist you further. Thanks for using ManageMyLife.com.

Read More
Desirea -
Sears Technician
July 07, 2013
See more answers
Q:

Why won't my dryer turn off?

A:

The dryer not shutting off can be a waste of electricity and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with the dryer timer problem, while you wait for your expert response.

Read More
Joseph P. -
July 03, 2012
A:

Thank you for submitting your question. If the dryer will not turn off when you open the door, replace the door switch (pn: 279347,$32.74). If it does turn off when you open the door, replace the timer (pn: 3976576, $104.39). You can order parts from our Sears Parts Direct web site. Here's a video on how to replace the door switch and here's a video on how to replace the timer. I hope this helps. Please reply back to this thread with more details if you require further assistance. Thank you for choosing Manage My Life.

Read More
Tykara -
Sears Technician
July 06, 2012
See more answers
Q:

How do I put a belt on my dryer/

A:

Dryer belt replacement can be a good home project with some directions and help. The expert will review this model to respond. I did locate a similar questions with information that may help. I also added the parts diagrams from Sears Parts Direct for this dryer. I hope this information helps.

Read More
Barbara H. -
April 21, 2012
A:

Thank you for your question and I understand your concern.

I added a YouTube video with the belt replacement procedure .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
April 23, 2012
See more answers

Top Parts