Model #11062824101 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Electric dryer will not run. Power at the wall confirmed. 11062824101 Kenmore Electric dryer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when  having trouble with the dryer.
 
Glad to help out.   Im  looking at your Kenmore Dryer model number 110.62824101.

First thing for safety and concerns to keep dryer running well is to check the lint screen and vent of air flow going out of the house.   If clogged up it could cause heating problems on any dryer.
 
To prevent a Blocked Vent Hood, once a year: 
 
1.  Clean any lint blockage from the exhaust vent hood.
2.  Make sure the vent hood flappers move freely.
3.  Check for screen/grate openings that allow bird or rodent nests.
4.  Replace exhaust vent hood if damaged.
5.  Check for good air flow while running the dryer.
Note: Poor airflow or decreased airflow indicates further vent system cleaning is needed.

You are saying that you have no power,  Dryer not starting correct?

No Power:
1.  Turn off the breaker then turn back on.
2.  Check the wall outlet for power.
3.  Check the power cord itself.
4.  Take a meter to the lid switch and check for continuity.
5.  Check out the start switch.
6.  Check out the timer switch.
7.  Check the motor.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
May 27, 2014
A:

1. Circuit breaker racked off then back on 2. 220 volts verified at the wall 3. Power cord seems fine but will verify power to the back of the dryer 4. Replaced lid switch with new from Sears Parts locally 5. Start switch verified and operates properly 6. Please explain how to verify the timer switch is functioning properly 7. Please explain best access to drive motor and how to test

Read More
Byron -
May 27, 2014
A:

Sorry again for your difficulties.   I see you are asking on how to test and verify the timer and the motor.

The timer can be checked with an Ohmmeter.  
1.  Please unplug the dryer.  

2.  Remove the screws in a counter clockwise motion.   Lift up the control panel backwards.

3.  Disconnect the two wires connecting the timer terminals with your fingers.  Remember best to markone set of the two disconnected wires with masking tape so you'll know where they go when you put it back on.

4.  Set an ohmmeter to RX1 setting.  Attach the 2 probes to the exposed timer poles where you diconnected the wires.  If the timer is working properly, the ohm reading should be 2,000 to 3,000 ohms.

How to verify motor is good:

1.  Again unplug the dryer.

2.  Open the cover of the lint screen.  Slide your lint screen out and remove the screws underneath.

3.  Use a flat-head screwdriver or putty knife to rasie the top corners of the appliance between the top and front panel.

4.  Grab teh clip in each corner under the top there at the front.  Squeeze the clips to remove them.  This will release the top from the front panel.

5.  Take out the screws on the sides of the front panel and bottom panel that is immediately below.

6.  Pull out the front panel.  Unplug the door switch from the wires on the back of the panel.  Push down on the bottom panel, tilt upward from the bottom edge to remove this part.  Now you can look down to the right at the bottom and see the motor.

7.  Pull the two wires from off the motor terminals, one at a time.   Make a not of where each wire connects so you will have no trouble re-installing them.  Each wire has a y-shaped clip on the end that pulls off the motor.

8.  Hold the 2 test rods on the meter to the motor terminals.   Set the meter to X1 so you can test for the continuity.  If the motor does not make a reading or the meter display numbers flash endlessly, then the motor is burned out and must be replaced.

If you know what you are doing good.   If not then would recommend a Sears service crew to help out.

Service
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: www.SearsServiceCrew.com
 
Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.


Read More
Larry L -
Sears Technician
May 27, 2014
See more answers
Q:

My Kenmore Dryer runs almost complete on Fragile, on normal shuts off prematurely. I've replaced HIGH-LIMIT THERMOSTAT 3387134, about to install Thermal Fuse?

A:

The dryer not completing the cycles can be frustrating. I found some information I am hoping will be helpful to you until your expert answers your question. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you with the dryer.

Read More
Marc -
September 05, 2012
A:

I believe i can help you resolve this problem but I may need some additional details. If an electric dryer will run then the thermal fuse is okay. If the dryer will heat on some cycles but not others then the timer is most likely at fault. If the dryer heats at all then I suspect the heating element and thermostats are okay. If the timer doesn't advance then I suspect the electronic control is at fault. If the dryer only heats in the delicate cycle but no other cycle then I suspect the timer is at fault. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
September 06, 2012
See more answers
Q:

How do I replace a belt on a kenmore dryer, model no 11062824101?

A:

I'm sorry to hear that you are having some difficulties with replacing the belt on your Dryer. I did some research for you at Managemylife.com and found expert answers to similar questions that may help until your expert can respond to your specific question, which i have attached the links attached below. I hope these links provided assist you.

Read More
Priscilla V -
December 19, 2011
A:

Thank you for your question.

I should be able to help you replace the belt on your dryer. First, you need to unplug the dryer and put on a pair of gloves. The inside metal parts of the dryer can be sharp. Then follow the steps below.

  • Remove the lint screen.
  • Remove the two screws in the top under the screen.
  • Pull the top forward to clear the two clips along the front. Then lift the top.
  • Remove the two screws securing the front panel.
  • Unplug the door switch harness and remove the front panel.
  • Lift the drum out of the cabinet and clean the inside of the cabinet with a vacuum.
  • Place a few drops of light oil on the roller shafts before reassembly.

I have also added a few images below, showing the steps for replacing the belt.

If you would like to watch a video showing how to replace the belt please click on this link .

If you run into problems, please reply below and I get right back to you.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 20, 2011
See more answers

Top Parts