Model #11062822100 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is the capacity for the dryer 80 series model 110.62822100?

A:

Thank you for choosing ManageMyLife.com. I understand how important it is to know the size of your dryer especially when it comes time to replace the unit. The capacity of your Kenmore Dryer model # 11062822100 is 7.0 cubic feet. If you would like more assistance, reply to this thread and I will be glad to assist you further. Thanks for using ManageMyLife.com.

Read More
Lokelani -
Sears Technician
September 03, 2013
Q:

My Kenmore 80 series model # 11062822100 stopped working. The plug is plugged in and the electric fuse is OK. What should I do?

A:

I know how frustrating it is when a major appliance begins to malfunction. I researched your question and was able to find a link that has information on this issue specific to your model. I attached the link below. I hope this helps.

Read More
Jackie S -
January 29, 2012
A:

Thank you for your question and I understand your concern.

The first thing to check and confirm is the voltage supply. The voltage supply should be checked and confirmed with a voltage meter. The voltage should be checked at the back of the dryer where the power cord is attached. Place the two meter leads across the two outside terminals and it must measure 220-240 volts and then measure across the center terminal to both outside terminals and it should measure 110-120 volts. Note: I do not recommend measuring voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dryer. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

If the voltage supply is correct, the next component to check is the thermal fuse. The thermal fuse is located on the blower wheel housing. The thermal fuse can be disconnected and tested for continuity with an Ohm meter.

I added a YouTube video showing how to access the thermal fuse and a video showing how to test the thermal fuse. If you find a faulty thermal fuse, the part number of the thermal fuse is 3392519 which can be ordered from Sears PartsDirect . A dirty or restricted venting system can cause the thermal fuse to fail. Be sure to check and clean the vent system. Don't forget to check the outside vent cap for restrictions and make sure the flapper door is opening.

This may be the issue. If not, please reply and I will be glad to assist you further.

Read More
Joey S -
Sears Technician
January 31, 2012
See more answers
Q:

Dryer lite on but not working

A:

The reason a dryer won't start can be hard to diagnose. The expert will review your model and provide some troubleshooting steps to help. If ay any point you decide you would prefer to have a technician visit to diagnose and make repairs, an option is the Sears Home Services scheduler below.

Read More
Barbara H. -
July 14, 2011
A:

Press in on the door switch and see if the drum light turns off when that switch is pushed in. If it doesn't go out, then the lid switch is your likely failure. You can order that door switch from the Sears PartsDirect website. The part number is 3406107. The first image below shows how to lift the top of the dryer to access that door switch. Be sure that you unplug the dryer before accessing internal components.

If the door switch appears to be okay, you could have a broken belt or a blown thermal fuse that would prevent the dryer from running. You can check the drive belt by lifting the top panel as shown in the first image below.

To check the thermal fuse, you can unplug the dryer and remove that back panel. The location of that thermal fuse is shown in the second image below. You can check it using the procedure shown in this brief video: Thermal Fuse Testing . If that fuse is blown, it will need to be replaced.

These tips may help you determine the cause of your dryer failure. You could also have a bad drive motor, a wiring failure or a bad timer that would prevent the dryer from running. If you need more help, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
July 16, 2011
A:

Excellent !!! It works replacing the fuse. thank you

Read More
jack reed -
July 17, 2011
See more answers

Top Parts