Model #11062082100 KENMORE Residential Dryer

  • Console Panel
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Dryer Top
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Heating element removal 11062082100 Kenmore Dryer

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore dryer.

From the information you have provided above, after researching model number 110.62082100. I have located some information that will help you replace the heating element for the dryer. Click here for information.  The part nu8mber for your element is 3387747.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

Read More
Benny23 -
Sears Technician
February 21, 2015
Q:

I have a Kenmore dryer model 110.62082100.

A:

Thank you for your question.  I am sorry for the problem with your Kenmore 110.62082100 Electric HE Dryer.  If the dryer is running but not heating then the potential causes of the no heat problem are the control board relay, thermal cut-off, hi-limit thermostat or element.  The diagram below may be helpful to you if a meter is available.   If no meter is available there is a trick to checking the relay, thermal cut-off and hi-limit thermostat without a meter.  You can reply below with any additional details or questions.  Let me know if you have a meter or feel comfortable using it. 

Read More
Fred M -
Sears Technician
November 25, 2013
Q:

dryer won't run 110-62082100

A:

A dryer is an appliance we depend on so much, when there's laundry to be done. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Yadira B -
February 02, 2013
A:

When an electric dryer doesn't run the most likely cause of the problem and the first thing to check is the thermal fuse located on the top back side of the blower exhaust. Check the image below for more details. The thermal fuse can be checked with a meter is one is available and you are comfortable using a meter. If there is no meter available then there is a trick to bypassing the fuse to see if it is the problem. Let me know if you would like to try this trick. You will need a small piece of insulated wire. Before removing the lower access panel be sure to turn the power off. I hope this helps. You can reply with any additional details for further assistance. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Fred M -
Sears Technician
February 03, 2013
A:

If the image above doesn't enlarge please try the image below.

Read More
Fred M -
Sears Technician
February 03, 2013
A:

I am interested in trying the trick to bypass the thermal fuse. Thanks so much for your assistance.

Read More
John -
February 04, 2013
A:

First unplug the dryer power cord then access the thermal fuse. The trick is to remove the two wires off the thermal fuse and join them together with a small piece of insulated wire with bare ends. Use some electrical tape to secure the connection and make sure no contact is made with metal. This will by pass the thermal fuse. If the dryer runs then that is the problem. Please don't continue to use the dryer with the thermal fuse bypassed. Good Luck.

Read More
Fred M -
Sears Technician
February 04, 2013
A:

Got it. Thanks so much.

Read More
John -
February 04, 2013
A:

Good luck and be sure to unplug the dryer before starting.

Read More
Fred M -
Sears Technician
February 06, 2013
See more answers

Top Parts