Model #11062066100 KENMORE Residential Dryer

  • Console Panel
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Dryer Top
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My dryer stops with error code E1. The model number is 110.62066100. How do I fix this?

A:

Core issue: Dryer stops with an error code E1.

Resolution:The machine control has detected a open thermal sensor. In some cases the control can be non-functioning and not accept any activation from the customer interface (keypad). To clear and restart the control follow the below listed steps:

  • Unplug or turn the circuit breaker off for a 30 second period.
  • Reconnect the unit to the power source, breaker back on or plug into the wall outlet.
  • Press the Pause/Cancel/Stop button twice to clear the PF in the display
  • Try to start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.

Read More
Tamira B. - Personal Solutions Manager -
Sears Technician
June 26, 2009
A:

Is there a part I can buy to stop this?

Read More
Madyson -
September 25, 2015
See more answers
Q:

Blowing Cut Offs, Replaced seemingly everything else, common problem according to threads ive read, HELP 110.62066100

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dryer and I do understand your frustration. Glad to help out. I'm looking at your model number 110.62066100 and a few things will cause the thermal cut off to blow. The first and most common is the lack of airflow. If air is restricted, the element will over heat. I recommend cleaning the lint filter, pull the dryer out form the wall, and disconnect the vent. Then start the dryer on high heat. The exhaust temperature should rise to about 160 or so and cool down to 120 then back on. If this is what the dryer does, we know the dryer is functioning properly and the problem is the vent. If the temperature does way above 160 degrees, I suspect a shorted element or shorted heater relay in the console. 


To check the element unplug the dryer and remove the wires from the element and ohm each terminal of the element to ground. You should not get a reading. If you do, the element is defective. If the element checks ok, move to the heater relay on the control board. I have provided you with the instructions for accessing the relay below. With the dryer still unplugged, remove the wires from the relay and ohm the terminals. You should have an open or ol reading. If it shows closed, the relay is defective. The thermal cut off is just a safety and should not be cycling the heat in the dryer. The temperature should be regulated by the main control and the thermistor. The thermistor is located on the blower housing and has a red and red with white stripe wires connected to it. The ohm reading of the thermistor should be around 10 k ohms at room temperature. The main control uses the thermistor to sense the temperature of the exhaust. Once the temperature reaches, 160 degrees on high heat the control turn the low voltage off to the relay. Without the low voltage, the relay should open and turn the element off. If the air flow is restricted the heated air will not pass the thermistor to warm it up. If it does not heat up the control never senses the temperature and will keep the relay closed. Without the air flow the thermal cut off is not cooled and will trip. Your dryer has a thermistor not a thermostat. The thermistor does not open and close. The resistance value changes with the temperature change. The only check is to ohm it out at room temperature and the reading should be around 10,000 ohms. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
January 19, 2015
Q:

Kenmore Elite Dryer Model 100 Beeps 3 times at start and nothing happens Kenmore Dryer

A:

Thank you for choosing SearsPartsDirect.com.  I want to thank you for being a valued member and will be happy to help with your washer. To better assist we would need a model number. The format is three numbers a dot then about eight more number for example 110.12345678.

If you have any further questions please re-post. Thank you for choosing Sears. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
August 11, 2014
A:

The model number is Kenmore Residential Dryer 110.62066100

Read More
John -
August 11, 2014
A:

The model number is Kenmore Residential Dryer 110.62066100

Read More
John -
August 11, 2014
A:

Kenmore Residential Dryer 110.62066100 My Kenmore Elite Dryer Model 100, beeps 3 times when pressing start and then nothing happens. When pressing any of the buttons they beep when changing options but when pressing start, just get three beeps.

Read More
John -
August 13, 2014
See more answers

Top Parts