Model #11062064102 KENMORE Residential Dryer

  • Console Panel
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Dryer Top
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

no heat 11062064102 Kenmore Electric dryer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is trouble with the dryer not heating.
 
Glad to help out.   Im  looking at your Kenmore Dryer model number 110.62064102.


First thing for safety and concerns to keep dryer running well is to check the lint screen and vent of air flow going out of the house.   If clogged up it could cause heating problems on any dryer.
 
To prevent a Blocked Vent Hood, once a year: 
 
1.  Clean any lint blockage from the exhaust vent hood.
2.  Make sure the vent hood flappers move freely.
3.  Check for screen/grate openings that allow bird or rodent nests.
4.  Replace exhaust vent hood if damaged.
5.  Check for good air flow while running the dryer.
Note: Poor airflow or decreased airflow indicates further vent system cleaning is needed.

When it comes to Electric dryers here are all the options to check on when not heating.
All can be checked with an Ohm meter for its continuity open or closed. 
 
You can see all these on the link below when clicked on.
 
Heating element which is key number 14
 
Thermal cut off switch which is both key 47 and key 48 together
 
ON the back of the blower is thermal fuse key number 59
 
Also on the back of the blower internal thermostat/thermistor key number 42
 
Again make sure you always keep  your lint screen areas clean.

pictures of the heating parts for model 110.62064102

Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs. Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
March 10, 2014
Q:

How do I replace belt in Kenmore Elite dryer?

A:

Replacing belts can be tricky. I found a previous expert post with diagram attachments for routing the belt. If you still have problems, add any additional detail in this thread so the expert will know what has been tried and can provide a better answer. Just copy and paste the link below. http://www.managemylife.com/mmh/questions/199647-why-is-my-kenmore-elite-dryer-model-11060992990-making-a-loud-squeaking-noise-and-sound-like-the-drum-is-loose

Read More
Barbara H. -
October 30, 2010
A:

Thank you for your question.

I have provided you with an image below. The image has how the belt should be routed if you were inside of the dryer looking at the motor. The belt should be tight when correctly installed. If it is not routed correctly, the dryer will not run. Once the belt is installed, make sure to check the door switch wires. I do not know how many times I forgot to connect the wires and the dryer would not start.

I hope this is helpful.

Please let me know if you need further assistance by replying below.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
October 31, 2010
A:

Thanks so much. It worked like a charm and the dryer is up and running.

Read More
betcha -
October 31, 2010
A:

I am glad you repaired the dryer yourself. Please keep us in mind if you have any other failures. Mark T.

Read More
Mark T -
Sears Technician
November 01, 2010
See more answers
Q:

How do I get into the front of my Kenmore model 110.62064102 dryer?

A:

Your dryer has a lower access panel and I'd suggest removing it first but the instructions below also so how to remove the front panel if necessary. Remember to unplug the dryer first before accessing any parts.

A certain amount of lint will always work it way past the lint screen so finding a small amount of lint past the filter is normal. I'd also recommend checking the lint hose in the back of the dryer for lint build up.

I hope this information helps to resolve this problem but submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
August 20, 2009

Top Parts