Model #11062042100 KENMORE Residential Dryer

  • Console Panel
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Dryer Top
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Where is the thermistor on a Kenmore dryer 110.62042100 located? 11062042100 Kenmore Dryer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

 

Read More
Joseph P. -
May 15, 2013
A:

Thanks for contacting manage my life about your dryer model 11062042100; sorry you are having a problem, I will be glad to assist you. Based on your description of the dryers malfunction I can say that a new thermistor will not solve the problem. However the location of the thermistor is on the blower housing accessible from the back of the dryer, remove the back cover and you can see the blower housing where air comes out and just above the air duct are two components one is the thermistor (thermistor controls heat only) the other (that could actually be the problem is a thermal fuse). Thermal FuseThe problem you describe could also be a bad door switch, wiring harnesses or the control itself. A complete diagnostic test would be needed to determine exact cause.   If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.If you need additional help please reply with more details and I will be happy to respond. Ron H.

Read More
Ron H -
Sears Technician
May 17, 2013
A:

_Always disconnect power supply before servicing the appliance and when testing live voltage be sure to wear proper safety equipment (gloves and eye protection) also be aware of sharp metals on product_

Use caution when servicing any appliance.

Ron H.

Read More
Ron H -
Sears Technician
May 17, 2013
See more answers
Q:

Why does my dryer shut off before the clothes is dry?

A:


In diagnostic mode, the dryer will sense an open thermistor by displaying a flashing E1 in the display. A flashing E2 would indicate a shorted thermistor. If you do not see either of these fault codes in the display during the diagnostic mode, then the thermistor is likely operating properly. If there are no faults detected, the display should show "88".

When the control is in the diagnostic mode, every input change of state will result in a beep. When you open the dryer door, you should hear a beep. You can test the moisture sensor by pressing a moistened cloth or finger across the sensor bars. When you do this, you should hear a beep as the board senses an input change from the sensor bar. If you hear no beep when conducting this sensor bar test, then you may have a loose wire, a failed moisture sensor or a bad control board. You could also have a bad thermistor even though it is not open or shorted as noted above.

If the moisture sensor fails the diagnostic test, you will need to schedule a service technician to conduct
further diagnosis of your problem. Resistance and wiring checks would be needed to identify the
failed component.

If you detect no failures in diagnostics, check your venting. Make sure that your flexible vent behind your dryer is not kinked or clogged. Also, check the exhaust duct to the outside of your
house for air flow restrictions. If you find no apparent problems, you will probably need a service
technician to diagnose and correct your problem.

Read More
expert -
Sears Technician
August 17, 2007
A:

Thank you. How do I go to Diagnostics mode?

Read More
Warren -
November 29, 2011
See more answers
Q:

kenmore elite dryer will not stop beeping

A:

In a situation like this you can do 1 of 2 choices and or both options, I attached this link below that I found in Manage My Life under the Answers button. This information will give some good advice that might help you while waiting on an expert answer. I attached the link below, I hope this helps!!!!!!

Read More
Raquel F -
October 11, 2010
A:

I’m sorry; on this type of symptom we will need a model number. Depending on the model will depend on the type of testing we need to perform. It sounds like a control board or programming problem.

Please reply with a valid model number for further assistance.

Read More
biker dave -
Sears Technician
October 12, 2010
A:

The Model # is 110-62042100. I hope this help, Thank you!

Read More
Dawnmarie95 -
October 12, 2010
A:

Thank you for providing the model number. On something like this it sounds like your describing a keypad problem. If the keypad has shorted keys you will have the symptom you described. The only way to confirm the diagnosis is to use an ohmmeter for testing the keypad functions. Another possibility is the main control board. First disconnect power to the dryer. I am sending you the access & testing instructions from the service manual covering this type of diagnosis. Pop off the console end caps to expose the hidden screws going down into the top panel, pull forward & flip the console up for service. Please click on the image below.

Read More
biker dave -
Sears Technician
October 12, 2010
See more answers

Top Parts