Model #11049182992 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Controls And Rear Panel
    3 Results
  • Agitator, Basket, And Tub
    3 Results
  • Transmission, Motor, And Pump
    3 Results
  • Suspension
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Won't drain 11049182992 Kenmore Washer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Yadira B -
May 28, 2013
A:

In most cases, the issue you are experiencing is related to the drain pump.

In order to access the drain pump will require placing the console in the service position, disconnecting the lid switch and removing the two gold colored cabinet clips. I added an image below with instructions on how to place the console in the service position and how to remove the washer cabinet in order to access the drain pump. To remove the pump involves removing both hoses and both pump clips. Be sure to have all the water drained before removing the pump hoses. Have a large old towel handy because some residual water will pour out of the hoses when you take them off the pump.

 Once the panel is removed, locate the pump in the back right corner of the washer. If the pump has a fan, try to turn it  by hand. Be careful you do not want to break it. If the fan is stuck there is something jammed in the pump. Try to wiggle the fan back and forth. If you can get it to free up you can plug the washer in and get it to drain. If it does not break loose, you have to drain the washer by hand. To drain most of the water lower the drain hose into a bucket. Once the bucket is full lift the hose and empty the bucket. You can also use a shop vac to remove the water. Once the water is drained, remove the hoses from the pump then remove the pump. You might be able to remove whatever is jammed in the pump once it is removed. If you cannot clean it out, you will need to replace the pump.

 

This could be caused by several different reasons:

  • Pump motor seized up.
  • Loose harness connection in the pump motor circuit.
  • Damaged motor start capacitor.
  • Pump motor winding failure.
  • Faulty wash pump drive circuit on the control board.

I hope this informaton helps. For more details please reply to this existing thread.  Thanks for using ManageMyLife!

Read More
Joe G. - Personal Solutions Manager -
Sears Technician
May 30, 2013
See more answers
Q:

washer leaving oil spots on clothe

A:

The washer leaving oil spots can ruin your clothe items and I am sorry for the inconvenience. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with your research while you wait for your expert response.

Read More
Joseph P. -
February 09, 2013
A:

First of all the oil in the transmission would normally end up on the floor and not inside the wash basket.  You may want to remove the agitaor and take a look under it.  There is a screw on the lowe half of the agitator between the fins.  Remove the screw to lift up on the agitator.  Beneath the agitator is a hub.  You can remove the basket by loosening the screw holding the hub.  Don't remove the screw. You can tap it to release the saddle block keeping pressure on the transmission shaft.  You might want to wipe the basket down and see if any oil stains transfers.  You can reply with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
February 10, 2013
See more answers
Q:

kenmore washer 110.49182992 stopped running

A:

Having an appliances we use daily to start having problems can be really frustrating. While you are waiting on an expert to answer your question, I suggest you set service with a Sears technician. I have attached the link below. Have a nice day!

Read More
Dezeray -
May 28, 2012
A:

Thanks for you reply Dezeray. Fortunately, I was able to fix it. I opened the top to access the switches, and the stationary part of the lid pressure switch was snapped. It simply was not depressing the switch when the lid was down. I wrapped a zip tie around it to hold the snapped part together, and now it works again. This is probably a common occurrence, as the part is weak at the fixed side of the pivot.

Read More
Hudson -
May 28, 2012
A:

Hi Hudson,

Thank you for submitting a question to Manage My Life.

I see that you have already fixed your washer. Good job! Let me know if I may be of further assistance, I will be happy to help. Please keep Manage My Life in mind for all of your do-it-yourself projects.

Landell

Read More
Landell -
Sears Technician
May 29, 2012
See more answers

Top Parts