Model #11047788800 KENMORE ELITE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Steamer, Pump And Motor Parts, Optional Parts (not Inc
    3 Results
Find part by diagram >

Question and Answers

Q:

My washer is Kenmore Elite Washermodel #11047788800 it is flashing sud-f35? 11047788800 Kenmore Elite Washer

A:

Thank you for contacting Sears. I will be more than happy to assist you with your Kenmore washer.

I can understand the frustration of your washer not functioning properly, after researching model number 110.47788800. the SUD-F35 error code indicates an issue with excessive suds If you see excessive suds in the washer, start using the right amount of high-efficiency (HE) detergent. The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor

I hope you found this information useful. Again thank you for choosing Sears. We appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
July 24, 2015
A:

What can I do so my machine will work properly.

Read More
Ellen -
July 24, 2015
See more answers
Q:

SUD and F35 error code, replaced pressure swith, did not fix issue, machine will not self test past C00, 11047788800 Kenmore Elite Washer

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore washer.  

From the information you have provided above, after researching model number 110.47788800. the SUD error code states there is excessive suds in the unit. this will happen if you put too much detergent in the washer or not using high efficiency detergent. So make sure you’re using HE detergent and the right amount. Now as far as the F35 code. The F35 error code indicates a pressure sensor error. The pressure sensor is the component that detects water level in the washer tub. Since you’ve already replaced this part and still does not fix the issue. The problem is going to be with the control board. This will most likely need to be switched out to clear the codes and get your washer back up and going. If you would like to have service set up to replace the control board you can do so by dialing 1-800-4MY-HOME.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

Read More
Benny23 -
Sears Technician
February 06, 2015
Q:

Wher is air trap located on washing machine model #11047788800 11047788800 Kenmore Elite Washer

A:

Thank you for contacting SearsPartsDirect.com with your question about the location of the airtrap on your Kenmore Elite Washer model 11047788800. I will be happy to help you with this. I have included the link below for your to view the Parts Diagram for the "Tub and Basket Parts" for your model. 
 
 
The air trap is key 14 on the diagram. It is held to the back of the Rear Tub by a screw. When replacing the airtrap, you should always check the condition of the o-ring and replace it if it is worn. I have included the links for the airtrap and o-ring in case you need to replace those parts. 
 
 
I hope this answers your question. If this is not the part you mean, or you need further assistance, please resubmit your question with additional details. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
July 19, 2014

Top Parts