Model #11045976404 KENMORE ELITE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Pump And Motor Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

Drain pump clean-out filter 11045976404 Kenmore Elite Residential washer

Q:

Water in the tub over night 11045976404 Kenmore Elite Residential washer

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your washer. Upon researching model 11045976404:  it sounds like the water level switch may need to be replaced. The water level switch allows the washer to fill up with water as needed, so when it fails it can allow water to enter the washer even when the unit is not in use. I have posted a link of the water level switch to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
July 09, 2015
Q:

Why is my Kenmore washer not draining and spinning?

A:

Why is my Kenmore washer not draining and spinning?

General Information: If the problem is the washer will fill and agitate but won't drain or spin at all then most likely the lid switch is the problem.

  • If the washer tries to spin but it doesn't drain then most likely the drain pump is bad or clogged.
  • If the washer won't drain and you hear the motor humming then it?s likely the pump has seized up.
  • If the washer will fill, agitate and drain but won't drain after the rinse cycle then the timer can be at fault.

Without the model number I'm unable to provide you with specific information. Please resubmit your question with the full model number provided.

Read More
Luis L -
Sears Technician
January 07, 2010
A:

my model number is ( 110.22642100 )

Read More
1bullion -
November 17, 2010
A:

For 1bullion: This type of problem is normally caused by a failed lid switch. Replacing that component will likely fix this problem based on your symptoms. You can unplug the washer and access the lid switch as shown in the image below. You can use the procedure shown at the bottom of that image to place an insulated jumper wire in the harness of the lid switch to see if the motor will run in the drain and spin mode with this switch bypassed. The wire colors going to the lid switch on your washer will be different (probably tan and gray). The basic procedure is the same. If the washer runs in the spin mode with this switch bypassed then the lid switch will definitely need to be replaced. You can order a new lid switch from the Sears PartsDirect website (see link below). The part number for the lid switch is 3949238. If the washer still won't spin with the lid switch bypassed, you could have a problem with the timer, the motor or the wiring between components. If you need more help, reply with additional details and we will assist you further. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. I provided a link to the Sears Service website below this response.

Read More
Lyle W -
Sears Technician
December 18, 2010
A:

Im having the same problem with my washer (model 11014212200) and I dont know if its cost efficient to even try and have the machine fixed. Its about 10 yrs old and up to this point hasnt given me any trouble. My son said that he wasnt confident enough to try and troubleshoot the problem. So, i had to take matters into to my own hands and start doing the internet searching thing. Im pretty sure that the lid mechanisms may be the problem. I just need to know how expensive is it to have it replaced by a professional? Is it cost efficient to just to dump it and invest in a newer model (a course it has to on sale!!!) or keep it? Thats the 64K $ question! I need professional advice asap!!!!!! HELP!!!!

Read More
valerie -
July 20, 2011
A:

Hello Valerie. It is likely that you have a failed lid switch (part 3949247). That part costs around $50. If you are able to replace that part and fix the washer yourself, then it is worth keeping. You can order that part from the Sears PartsDirect.com website (click on FIND PARTS link at the top of this thread). I provided a video of that repair in the image below. You can view that video to determine whether you can remove the cabinet and replace that switch. Be sure that you UNPLUG the washer before accessing internal components. Your washer will have plastic end caps on the console that need to be removed to access screws and open the console. NOTE: Before you order the part, you can verify the failure by jumping that lid switch harness with a piece of insulated wire as described in the above response. If you are not able to complete that repair yourself, the service by a technician will probably cost around $200 (this price includes parts and labor). It is likely that it will be more economical to replace the washer instead of repairing it in that situation. You can view current washer models on the Sears.com website. If you need advice or help with selecting a new washer, let us know. If you need more help with the repair, reply with additional details.

Read More
Lyle W -
Sears Technician
July 21, 2011
A:

Thanks! that was the problem!!! The above information was wonerful!

Read More
Melanie -
August 14, 2012
A:

Thanks for letting us know what you found. We like to be accurate with our advice and it is great to hear when an appliance it fixed. Let us know if you ever need more assistance.

Read More
Lyle W -
Sears Technician
August 14, 2012
A:

I am having similar problems with my washer it doesn't spin or drain but I can hear the motor humming. What can I do? model # is11045976404

Read More
esther -
February 28, 2013
A:

If you hear the drain motor humming when the washer does not drain, then you could have a clog in large item filter of the drain pump. You can manually drain the washer and access that large item filter as shown in the image below. Be sure that you UNPLUG the washer before accessing internal components. If you find a clog in that area and clear it, then the washer may drain and spin properly. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
March 01, 2013
A:

My Kenmore washer 11022642100 isn't spinning or draining. I don't think its the lid switch because, the dogs are busted(upper part of agitator spins freely, your hear the dogs rattling around, and it wont grip the lower at all) and the lower part of the agitator will not turn under hand power. When put in wash cycle you here the motor hum(hoses disconnected) and I know the pump isn't clogged because I took it apart. Hoses are clear as well. Clutch spins freely as well. Was thinking it was the gearcase but wanted expert advice before I spend 130$. Also wanted to know if there is any other part I need to replace as well if I'm replacing gearcase. Let me know. Can replace lid switch too if you think that needs to be done. But that gearcase feels locked up for sure. Thanks Matt

Read More
Matt -
April 06, 2014
See more answers

Top Parts