Model #11045862402 KENMORE ELITE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Pump And Motor Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

dispenser leaking water 11045862402 Kenmore Elite Residential washer

A:

Thank you for choosing SearsPartsDirect.com. I will be more then happy to assist you. Looking at the information the pressure switch could be the main issue. See that you have already replaced the water hoses and water valve. The pressure switch has a hose that is attached just that hose could be off and needs to be put back on. The pressure switch is located on the right hand side inside the unit. When you do locate it I have a test that can determine if it need to be replaced. Take the tube and blow into it, If you can't blow thru it aisle, then its fine. But if you blow and it goes right thru then it needs replaced. If you are not comfortable doing this repair you can Click Here to schedule a technician or call toll free 1-800-469-4663. Hope this information has help you, any further questions or concerns. You will have to post a new question because at this time I can not reply to any comments. Aging, Thank you for choosing SearsPartsDirect.com.
 

Read More
Samantha A -
Sears Technician
May 29, 2014
A:

Based on your response, I need clarification. When I blow into the hose, am I blowing back into the pressure switch thru the hose or blowing into the hose toward the other end?

Read More
Thomas -
May 29, 2014
See more answers
Q:

Sitting water in wash tub 11045862402 Kenmore Elite Residential washer

A:

Thank you for your question.  I am sorry for the problem with your Kenmore110.45862402 Front Load Washer.   From the description of the problem I suspect the Water Inlet Valve is the problem.   To prove this turn the water spigot behind the washer off and see if the tub continues to fill with water overnight.  The valve can fail is such a way that it allows a small amount of water to leak past even if the washer is unplugged.  I hope the helps.  You can reply below with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
October 13, 2013
Q:

where is lint catcher on kenmore elite quiet pak II washer?

A:

Finding out exactly where the filter is located on your washer may seem like a difficult task. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Yadira B -
March 03, 2013
A:

good luck getting the answer that you need. i have been trying to get answers for 2 days and have been sent to websites that do not help.

Read More
carol -
March 03, 2013
A:

I know that it can be very difficult to have issues with your washer. Your washer will not likely have a lint filter.  I did not see one available for it either. The majority of the lint is held in suspension and pumped down the drain along with the drain water. We rely on the dryer to remove any lint that may remain on the clothes. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
March 04, 2013
A:

Thanks for contacting ManageMyLife.com. I understand your concern with your locating the lint screen on the washer. We are here to help. The lint screen filter is located at the pump. The image below shows how to clean the filter. I hope this helps.

To order washer parts, please visit SearsPartsDirect.com with the model number.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Read More
John H -
Sears Technician
March 04, 2013
See more answers

Top Parts