Model #11044934200 KENMORE ELITE Residential Washers

  • Top And Cabinet
    3 Results
  • Door And Latch
    3 Results
  • Control Panel
    3 Results
  • Dispenser
    3 Results
  • Tub And Basket
    3 Results
  • Pump And Motor
    3 Results
  • Pedestal Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

need to know what F02 code kenmore elite HE3t

A:

Having an error code on a washer can be inconvenient and keep your washer from working properly and I will be happy to help. While you are waiting for your expert answer, I suggest you add to the thread of this question and include the full model number of your appliance so that the expert can provide you with a more detailed answer. I did manage to find a link that describes a similar problem to the one that you are having with your washer. I hope my link is useful.

Read More
Joseph P. -
May 17, 2011
A:

The F02 code pertains to the drain pump. From the description you give the drain pump is not working or is not working very well.

The first thing to do is to remove the lower panel and access the drain pump. This drain pump has a filer that can be removed and cleaned.

Refer to the images below for help with this. Remember to unplug the washer first.

You will need a shallow pan to catch the water that will spill out when the filter is removed. If you don't have a shallow pan then a couple of beach towels will help.

Excessive suds can also cause this problem.

Clean the filter and see if that helps. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
May 18, 2011
A:

Hello, I had this same problem and I ran the diagnostic test which proved that the drain pump is no longer working. (It will not drain at all.) We cleaned it out but now I just need to know what the part # is to replace it. Help? Thanks soooo much!

Read More
Amanda -
August 10, 2011
A:

Amanda: Including the model number would help me provide the correct part number of the drain pump. Reply with the model number or you can look up the drain pump part number yourself and order it from SearsPartsDirect or you can call 1-800-366-7278 [Sears PartsDirect | http://www.searspartsdirect.com?sid=MMLxexpertxmerch]

Read More
Joey S -
Sears Technician
August 10, 2011
A:

The model of the washer is: 110.42922200 or 110.42932200 (I can't open it at the moment as I have yet to open the bottom of the washer back up and the door is locked)

Read More
Amanda -
August 10, 2011
A:

Amanda: The part number of the drain pump assembly is #280187. I also added some information in the images below if needed. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
August 10, 2011
A:

I have a kenmore elite HE3t and am having the same issue with the f02 code and the suds alert. i have checked the drain hose checked the filter and get the same results. i have read your advice and just want to make sure i just need a pump replacement and not the mother board as i hate to keep chasing one problem after another.

Read More
David Wagner -
November 27, 2011
A:

i forgot to add the model number is 11042926220

Read More
David Wagner -
November 27, 2011
A:

David: If the drain pump is operating and you can confirm that it drains water then it will not likely need a control board. If you�re using too much detergent or the wrong type, it can also cause F02 and SUDS to display. If it is draining water and the F02 and SUDS fault codes do not clear, then you likely have a water level pressure switch failure. If the water level pressure switch does not reset after the water has drained, F02/Suds will not clear. If the water is not draining then the drain pump may be faulty. Additional details would be helpful. Does the drain pump run or not? Does it drain any at all?

Read More
Joey S -
Sears Technician
November 28, 2011
A:

I do not know if this tip will work with the Whirlpool built machines but it does with the Frigidaire (Electrolux) ones. Couple a Wetvac to the discharge hose and suck the water out of the drain line and filter, I just block off the gap between the Wetvac suction and the drain pipe with my hand and it saves a lot of mess. It will likely not work should the filter be totally blocked.

Read More
biguggy -
November 28, 2011
See more answers
Q:

Lot of vibration in waher tub 11044934200

Q:

My He3t automatically fills up after it has been emptied & switched off? 11044934200 Kenmore Elite Automatic washer horizontal axis

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the washer.
 
Glad to help out.   Im  looking at your Kenmore Washer model number 11044934200.

Sounds like your water valves on the back of the machine (especially the cold water side) didn't close up and needs to be replaced.

Water valve for the model 
11044934200.      

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
May 30, 2014

Top Parts