Model #11029832800 KENMORE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Washer timer controller 110.29832800

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when doing repairs on the washing machine
 
Glad to help out.   Im  looking at your Kenmore Washer model number 110.29832800.

I see you are looking to replace your timer.   Please look at the picture below.   Look at key number 8.   That is a spring clip and just need to take something like a putty knife and press in on the spring clips that will be on each bottom side of the control panel.  

1.  Unplug the washing machine.

2.  Remove the knobs.

3.  Press in on the spring clip.

4.  Remove the end panels of the control panel

Good luck

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
May 28, 2014
Q:

Washing Machine Kenmore 800 with auto sensor for water

A:

duplicated question

Read More
James -
March 30, 2011
A:

duplicated question

Read More
James -
March 30, 2011
A:

Thank you for your question.

I am sorry you are having a problem with the washer. Usually when we have this problem, it is a defective load sense switch. The contacts in the switch fuse together and the washer starts agitating before the water comes in. a simple test is to unplug the wires from the switch and check the operation. If you would like to do the test unplug the washer and open the console. I have provided the instructions for opening the console below. Once the console is opened look for the component that has the clear hoes connected to it. Then remove the wire connectors from the switch and check the operation. If the washer does not fill or agitate the switch is the problem. The load sense switch can be ordered from our parts website: Sears Parts Direct .

A defective load sense switch will cause the washer to fill with a small amount of water after the final spin.

If you need further assistance on the washer, please reply with more details and a model number.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
April 01, 2011
A:

I have a Kenmore 800 washer, model number 110.29832800, that has does not fill with water or agitate. The only thing that it does that lets me know it still works is that it will drain and spin but only after I move the dial to the spin cycle. I am guessing that it is the load sensor switch but am looking for reassurance before I waste the money and that is not the problem. I have already took the control panel off and inspected the load sensor switch but do not notice any visible damage. Is there any other possibilities for this problem or is it safe to say it is the load sensor switch. Thank you for any help!

Read More
Steven -
December 05, 2011
A:

Steven, you are probably correct on the load sense switch but I recommend doing some checks to confirm it. I am sure you have checked the water supply to the washer already. Next, you will need a meter to do live voltage checks. If you have a meter and feel confident in checking live voltage, please reply below with the complete model number. Once I have the model number I will be able to look up the diagram for your model and provide you with the correct checks.

Read More
Mark T -
Sears Technician
December 06, 2011
A:

My Model number is 110.29832800. I tested the voltage output on the Load Sensor Switch and it measured 120vs. So based on what I have read, that is correct and should not require replacement. After that I decided to check the Water Inlet Valve and from my understanding it should be producing about 110vs but mine is only producing around 20vs. Is this correct information and if so would the water inlet valve prevent the washer from filling with water and agitating as well. I was pretty certain that it was the load sensor switch based on the readings but it seems to have passed the test. Kinks or debris in the hoses and netting are not issues. Thank you for your assistance.

Read More
Steven -
December 07, 2011
A:

Thank you for the reply. I have looked up the model number you have submitted. I have posted am image below that shows where to place the meter leads. The test should be done with the washer plugged in, timer set to a wash cycle, and the timer knob pulled out. Please make sure to use caution when doing these checks because it is live voltage. Wearing rubber gloves will better insulate you. If you have 120 volts on meter one and less than 109 on meter 2, the load sense is defective. If you have 120 on meter 2 and less than 109 on meter three the timer is the problem. I hope this is helpful. If you need further assistance, please reply below with the details of the checks above.

Read More
Mark T -
Sears Technician
December 08, 2011
A:

Mark,I was reading your reply to Steven,I love to see the diagram so I can do the live Voltage checks.But I cannot find anything to click on to display the diagram.Could you please put the link back? My name is Shillion.

Read More
shillion -
November 07, 2013
A:

I am sorry you do not see the image. I suspect you are viewing this question on our searspartsdirect site. For some reason we are having a problems with the images showing up there. Please click on the following link. Washing Machine Kenmore 800 with auto sensor for water It will take you to our managemylife.com site where you can view the images. Please let me know if you need further assistance. Thank you Mark

Read More
Mark T -
Sears Technician
November 09, 2013
See more answers
Q:

My Kenmore 800 washer will not start.

A:

Having a properly working washer is very important. The washer not starting can very frustrating. I found some information for you that I am hoping will be able to help you out. Please click here:[Washer Not Starting]. Your expert will also help answer your question. It may take two business days for your expert to reply . I do hope that everything works out.

Read More
Marc -
June 12, 2013
A:

Hello Gentry. I am sorry to hear about the problems that you are having with your Kenmore Washer Model 110.29832800. 

 

Make sure that the washer is plugged into a working electrical outlet. That basic troubleshooting step should not be overlooked. 

 

On that type of washer, it will not start (or even fill) if the lid switch is broken. I recommend that you check that component first. Unplug the washer to disconnect electrical power before accessing internal components. The image below shows how to open the console to access that lid switch. Check the metal tab on the washer lid to make sure that it is activating that lid switch. If you are confident that you can safely insert a jumper wire in the lid switch, then you can bypass it for a brief test to see if the washer will start with that jumper wire in place.  The second image below shows how to place a short, insulated jumper wire into the harness of the lid switch to bypass it for testing. You should not have to remove the cabinet on your washer to complete that task. Note: Do not continue to operate the washer with that lid switch bypassed. Restore the original wiring configuration to the lid switch and replace that component if the washer runs with the lid switch bypassed.

 

If you need more help, reply with additional details.

 

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services Washer Repair. 

Read More
Lyle W -
Sears Technician
June 14, 2013
See more answers

Top Parts