Model #11029522801 KENMORE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Unidentified Part

A:

I understand how frustrating it could be when it comes to repairing and replacing parts on the washer. While you are waiting for a detailed reply from an expert I recommend visiting the Sears parts direct website were you can vie a full parts list and diagram of your model. I have provided the link below. Hope this helps!

Read More
Priscilla V -
March 15, 2012
A:

Thank you for your question and I understand your concern.

Thank you for the image of the part in question. The part in the image is one of two or possibly 3 pins used to lock the suspension from moving during shipping. It is not needed. You will likely find three simi-transparent little cups below the triangular base with the remainder of the pins. These pins prevent the tub from moving around during shipment. When the washer is delivered and set up, the yellow shipping strap attached to the back of the washer is connected to each pin and when the shipping strap is pulled out, the pins drop into the little cups to prevent them from falling on the floor causing one to wonder what part fell out. These pins are used for shipping only.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
March 15, 2012
A:

Thanks for the responses. This website has helped me to resolve my issue and ease my mind because I promised my wife that the wash machine will be finished today. Again Thanks Tyrone

Read More
Tyrone -
March 15, 2012
A:

Tyrone: You are most welcome. Thank you for using Manage My Life.

Read More
Joey S -
Sears Technician
March 15, 2012
A:

Hello, I have a Kenmore model 106.59512991. I am trying to replace the water fitting line (part #2180225) that runs from the connection under the front panel through the freezer door hinge to the water dispenser in the door. I can't figure out how to access the inside for the door to feed the line through. Can you assist?

Read More
George -
March 19, 2012
A:

George: Take the line connection loose at the bottom of the door, and take the dispenser panel off. It can be pried off from the bottom. Pry it out and lift it up and off. You will have access to the water line. You may have to remove the nozzle bracket to have full access the tubing. You will need to pull it out from the dispenser. If you only pull it out a little and attach the new line to the old with tape, you could pull the new line in from the bottom by pulling on the old water line. There is channel the tubing will slide through. NOTE: The door is foamed in place to the inner liner and the outer door panel can not be separated from the inner liner.

Read More
Joey S -
Sears Technician
March 19, 2012
A:

Thanks, I'll try that.

Read More
George -
March 19, 2012
A:

I need to take top off on fisher & paykel washer GWL 15

Read More
John -
March 19, 2012
A:

I have a kenmore 500 clothes washer and would like to lay it on its side to ship. I'm wondering if I should be worried about oil leaking from the tranmission housing (vent?) The model number is 110-29522801.

Read More
jeff -
March 19, 2012
A:

John: This initial thread pertains to a Kenmore direct drive washer. Please ask your question in a formal question so we can keep this thread directed to a Kenmore direct drive washer. This will prevent confusion for others. Thank you.

Read More
Joey S -
Sears Technician
March 20, 2012
See more answers
Q:

My Kenmore 500 washing machine leaks. Model # 11029522801

Q:

water not filling up just trickiling in 11029522801 Kenmore Residential washer

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your washer. Upon researching model 11029522801; it sounds like the water valve may need to be replaced. The water valve allows the water from your home to enter the washer as needed, so when it fails it can cause the washer to not get the amount of water needed. I have posted a link of the water valve to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
March 25, 2015

Top Parts