Model #11028892790 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is the function of 3352282 sensor 11028892790 Kenmore Automatic washer

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
Sorry to hear that the washer overflowed on you during operation, I know how concerning that is to have occur.
The sensor you refer to of 3352282 is referred to as an ETC sensor, or an electronic temperature control sensor. This sensor would regulate the temperature of the water going to the tub.
A failure with this sensor would not cause the tub to overflow as you've experienced. In the controls section of the washer, you have a water level switch, also known as the pressure switch. It's likely it would be this part that would cause the symptom you've experienced. Before replacing the switch however, make sure the pressure hose is connected properly, because if it came off the connection, it could also cause the overflow issue.
For convenience, I have provided a blue link below that yiou may click on to be directed to the SearsParts site to view and purchase the switch if needed.
If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-349-5071, or click here to be directed to the page to set up service.

Water Level/Pressure Switch for Model 11028892790

Hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
June 14, 2014
Q:

how do I repair my agitator? 11028892790 Kenmore Automatic washer

A:

Thank You for contacting SearsPartsDirect.com
I understand your frustration when your washre is not working correctly. Based on the information you have provided it sounds like you need to replace the agitator dogs and cam. The dogs have little teeth on them that get worn down over time. I have attach the links for the part and a helpful repair video. Just click on the blue link below to be taken to the pages.

Agitator Repair Kit for Model 110.28892790

Video: How to fix the agitator on your washing machine


If you need further assistance, please resumbit your question with additional details. Thanks for visiting SearsPartsDirect.com

Read More
Desirea -
Sears Technician
January 11, 2014
Q:

crud in washing machine

A:

The washer having flakes in the water can really cause some concern and I will be happy to help. I suggest you add to the thread of this question and include the full model number of your washer so that the expert can provide you with a more detailed answer. I am adding a link below to help you locate the model number. I am also adding a second link with a similar question. I hope this helps with your washer troubles while you wait for your expert response.

Read More
Joseph P. -
December 12, 2012
A:

The model number is 110.28892790

Read More
Patricia -
December 12, 2012
A:

Thank you for your question and I understand your concern.

Based on your symptom and details I would suspect the inside wall of the outer tub is covered in layer of crud. You will need to remove the washer cabinet and the tub cover in order to access between the spin basket and outer tub. NOTE: Disconnect the power supply from the power source before servicing.

The control panel will need to be placed in the service position in order to disconnect the lid switch quick disconnect plug and to remove the two cabinet clips before the cabinet can be removed. Remove the left and right side end cap covers. Lift the top of the end cap cover up and then pivot it towards the front of the washer to remove. Remove the screw located at the bottom of each end cap. Slide the control panel towards the front of the washer and pick it up and hinge it over the rear panel. Disconnect the three wire lid switch connector from the top of the washer. Use a flat blade screwdriver and place the tip in the first valley closest to the front and push the handle back to pop the cabinet clips off. Open the lid, tilt the top of the washer towards you and walk it away from the base. The tub ring/cover has plastic tabs to pry away from the tub to release. It helps to push down on the tub cover while prying out on the locking tabs. Remove the tub cover and you will have enough access to scrape the crud off from the tub which collects around the water level line.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
December 13, 2012
See more answers

Top Parts