Model #11028884790 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator Basket And Tub
    3 Results
  • Brake, Clutch, Gearcase, Motor, Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

WASHER WILL NOT AGITATE OR SPIN MODEL 110.28884790 SERIAL CG3303924

A:

Thank You for choosing Sears PartsDirect.com. I regret to 
hear that you are having issues with your washer and do understand your frustration. Glad to help out. Im looking at your model number 110.28884790 and from what you are describing it seems like the lid switch is damaged. I recommend testing the switch. 
  1. Unplug the washer to disconnect electrical power.
  2. Remove the two plastic end caps on each side of the console. NOTE: Some models do not have removable end caps.
  3. Remove the screws on each side of the console that secure it to the top panel. NOTE: Some models do not have screws. If not, release the clips on each side using a putty knife.
  4. Pull the console forward and hinge it up and back over the top of the back panel of the washer.
  5. Release the clip on each side of the cabinet that secures it to the back panel (see image).
  6. Pull the cabinet forward to access the lid switch wire harness. Unplug the wire harness.
  7. Pull the cabinet off of the washer. You now have access to remove and replace the lid switch.

Read More
Sherman_G_Wallace -
Sears Technician
December 05, 2013
A:

I ALREADY MENTIONED THAT THE LID SWITCH IS WORKING PROPERLY. WHAT ELSE YOU GOT?

Read More
alan -
December 06, 2013
See more answers
Q:

My Kenmore washer model # 110.28884790 shakes violently and walks across the floor during the spin cycle does not matter what size load. Any Ideas?

A:

When I am having a problem with my appliance what I like to do is refer back to my owners manual because usually it provides me with lots of handy troubleshooting. I would highly recommend for you to review your owners manual. If you do not have yours I have managed to locate one here on the Manage My Life website. I attached the link below for you to view while you wait on your answer from an expert. I hope this can help you out with the problem you are having with your washer.

Read More
Dezeray S -
January 10, 2011
A:

From what you're describing I suspect the rear self-levelers. The rear legs on this model of washer are self-leveling. It sounds like you need to reset the self-levelers. First disconnect power to the washer. With an empty washer tilt the unit up in the back. Have someone hold the washer up for you & tap on the bottom of the feet with a pair of pliers or small mallet. This should release the legs if they were in a bind. Now when you rest the unit back on the floor the self-levelers will self-adjust & level the unit out.

Another possibility is if the shipping pins are still in place. This type of repair will be complicated if this was not done during the original installation. The base & suspension plate have cotter pins to keep them from separating during transport. The pins will fall into a holding spot for the life of the unit. You can check if the pins are in the cups fairly easily.

Remember to disconnect power & pull the washer out far enough to safely lean the unit back against the wall. Use a flashlight to look for 2 small clear plastic cups mounted to the frame below the suspension plate. If you do not see the pins in the cups, I suspect they were never removed. If you see the pins I suspect the suspension springs or plate is damaged causing the out of balance condition.

After making these initial checks & inspections please reply back with your findings if you still need further assistance.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: sears home service

Please click on the image below.

Read More
biker dave -
Sears Technician
January 11, 2011
See more answers

Top Parts