Model #11028882791 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator/basket/tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Spin Cycle 11028882791 Kenmore Automatic washer

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your washer and do understand your frustration. Glad to help out. Im looking at your model number 11028882791 and the lid switch will cause the machine to turn off and on. I recommend replacing the switch.  3949238 . 

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page.
 
If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com
 

Read More
Sherman_G_Wallace -
Sears Technician
February 04, 2014
A:

Thanks Sherman, but after reading about this in other conversations I jumped the lid switch with a wire and it still went on an off. I have discovered that the motor armature has horizontal play and there is a kill switch in side the motor. A temporary solution was to put a small spring between the pump and motor to keep the armature back. That worked but it put pressure on the pump seal and it started to leak, I took the spring out and cut it in half and the leak is almost gone. What would cause the motor armature to have that much play and is there a fix to the motor other than a replacement?

Read More
Dave -
February 04, 2014
See more answers
Q:

How do I replace the lid switch on a model 110.28882791 washer?

A:

The instructions to access and change the lid switch are in the image below. Remember to unplug the washer first.

Your washer has two end caps that must be removed to access the two screws holding the console down.

I hope this information helps to resolve this particular problem for you. If any other questions come up then submit another question with any additional details for further assistance with this problem.

Read More
Fred M -
Sears Technician
June 03, 2009
A:

Sorry to jump in on this old thread but my lid switch works but only sometimes?? it seems the pointed piece on the lid no longer reaches far enough down to engage switch any help?

Read More
Greg -
July 22, 2013
See more answers
Q:

Control knob spins on Kenmore washer. Can't remove with pliers.

A:

A washer is an appliance we depend on so much, when there's laundry to be done.  While you are waiting for an expert to respond, I have added a helpful link that may provide information to assist you with your question.

Read More
Yadira B -
June 03, 2013
A:

Thank you, Yadira. I read that solution, but it assumes that something I already tried will work (gripping the shaft with pliers). Unfortunately, it didn't work, so I'm still stuck.

Read More
James -
June 03, 2013
A:

Hi,

 Thanks for contacting ManageMyLife. I understand how frustrating it is having trouble with your appliance not working.

Try this, push the knob in and turn the knob counterclockwise.  This  should allow the knob to turn off the shaft. 

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
June 06, 2013
A:

I tried pushing it in and it still spins in either direction. In no position does it grip at all, just spins. Do you know any other way to get it off?

Read More
James -
June 06, 2013
A:

James, the timer index seems to be broken and there is one possible trick you can try before breaking off the knob and ordering a new know. Open the console and check the backside of the timer. See the pictures below

Read More
Bill__W -
Sears Technician
June 07, 2013
A:

Hi, Bill. Okay, I got the donut pulled out from the back of the timer and the index is up. The knob is pushed in in the front. That is the correct position, right? The knob still spins in both directions, though. I guess I need to break off the knob. How do I do that without damaging the control panel?

Read More
James -
June 07, 2013
A:

Grab the knob with a pair of pliers and flex one way and then the opposite way being careful not to flex the panel. Another way I have used is the dremmel tool that I have and cut the knob off the shaft then the shaft can be cut off.

Read More
Bill__W -
Sears Technician
June 07, 2013
A:

That worked. Thank you very much!

Read More
James -
June 07, 2013
A:

Now all you need a the knob and you are back in business. Good Job.

Read More
Bill__W -
Sears Technician
June 07, 2013
See more answers

Top Parts