Model #11027052602 KENMORE ELITE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Motor, Basket And Tub Parts
    3 Results
  • Pump Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

Sears Kenmore Oasis Elite Washer model 110.27502602 11027052602 Kenmore Elite Residential washer

Q:

Why does my Kenmore washer (model 110.27052602) gets unbalanced with every spin cycle. It makes a loud grinding noise and goes unbalance even without a load.

A:

Good morning... I can fully understand your concern regarding this grinding issue. I did locate a link that will discuss your situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might be wrong with your washer and have a nice day.

Read More
Henry -
March 11, 2013
A:

You could have a problem with the bearing in the bottom of the outer plastic tub. Rust on the drive shaft could also cause that problem. There is a possibility that an item is caught between the outer plastic tub and the stainless steel spin basket.  You can unplug the washer and remove the spin basket to check that last issue. If you find and remove an item in that area, then you may be able to fix this problem yourself. 

 

If you find rust on the drive shaft, then you may be able to eliminate that rust and fix the problem.

 

I you need parts, you can order them from this page: Kenmore Washer Model 110.27052602 Repair Parts. 

 

If those tips don't help, then you will probably need to have a service technician diagnose and repair this failure. The spin basket and the outer tub of the washer have a 10 year parts warranty. You would have to pay for the labor of a technician if those parts need to be replaced. The bearing in that outer tub is not covered by the 10 year parts warranty. Your model appears to be less than 10 years old. You can schedule service on this page: Sears Home Services Washer Repair. 

 

If you need more help, reply with additional details and we will assist you further. 

Read More
Lyle W -
Sears Technician
March 12, 2013
See more answers
Q:

kenmore elite oasis washer repair

A:

Having your washer begin to display error codes and not function properly can be very frustrating. I did some research on the issue and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
December 14, 2012
A:

I'm trying to avoid replacing the control board. If its the transducer for the water level, I would be able to replace the part if I can get honeywell to send it to me. They want a part number for the transducer which isn't on the sensor. whirlpool won't give any information on the circuit board and kenmore.com was useless too. All they would offer was to schedule an appointment for a repairman to come to my home to diagnosis the problem, then replace the circuit board. Total cost would be more then the machine is worth. I suspect that the part would probably cost less then $5.00 including shipping.

Read More
Bill -
December 14, 2012
A:

Error codes like this one do require several checks to rule out before spending money on a new control. I see Julio provided an excellent expert answer for this problem for troubleshooting. There really is not anything I can add to that answer. I have added an image with the troubleshooting straight out of the tech manual for this problem. As to the part on the control module, it is not sold seperately by Sears Parts Direct. You may want to check outside sources with the complete control number to see if you can get an individual component but that is not something I could recommend. The control is manufactured to operate as one part. I am sorry we can not be of more help. Please reply if further assistance is needed. Thank you for using Manage My Life.

Read More
Barbara H. -
Sears Technician
December 15, 2012
A:

Thank you for your advice. I'll check the water level hose for kinks and moisture. I don't know what the airdome is but I'll find it and check for lint or flashing. I'll look for the R on the control board.

Read More
Bill -
December 15, 2012
A:

I've tried all the suggestions given to me in this forum and others. The first thing that I did was to remove the control board and clean all the contact points including the water inlet solenoids and sensor connections. Then I replaced the water inlet assembly. Next was the motor circuit board at the bottom of the machine. No problem there. Then took the tub out of the machine to check for debris in the water dome and water level tube going to the control board transducer. I blew air through the tube at the control board end and bubbles came out at the air dome. After all this I'm still getting F1 code when the machine is filling the tub with water. As usual I push the stop button and then the start button. This usually gets the fill cycle working again. When the machine gets to the rinse cycle I have to repeat the stop and start to get it to finish washing the clothes. Is there anything else to look for before I replace the control board?

Read More
Bill -
December 17, 2012
A:

Since you have taken the machine apart and checked all the areas that cause this error with no resolution, it appears the control assembly will need to be replaced. It is part # W10189966 and can be ordered at the Sears Parts Direct link below. The images below will help access and replace. I did go back through all the diagnostic information. It does point to the control. Let me know if anything further is needed.

Read More
Barbara H. -
Sears Technician
December 20, 2012
See more answers

Top Parts