Model #11026934691 KENMORE Residential Washers

  • Control Panel
    3 Results
  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Detergent And Rinse Dispenser
    3 Results
  • Water System
    3 Results
  • Wiring Harness
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How do you remove the agitator in a Kenmore 90 series, model 110.26934691?? 11026934691 Kenmore Residential washers

A:

Thank you for choosing Sears Parts Direct. I can certainly assist you in locating the instructions to remove the agitator on your mower. I did look into the model number you have provided and I have found information to assist you. 


After removing the dispenser #22 & cap #1, pops off with a screwdriver, use a 1/2 inch ratchet extension or a pair of needle nose pliers with the tips spread apart to unscrew #14 the spring retainer, counterclockwise. After removing the spring retainer you can lift up & off the auger #6 the breakaway part. Now you can use a 7/16 socket to remove the #19 screw. Lift off the agitator for complete removal.
Let me know if this helps.


You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.

Thank you for your question. Have a great day. 




Read More
Natasha12 -
Sears Technician
May 05, 2014
Q:

How do I remove the drive moro assembly to replace the belts? 11026934691 Kenmore Residential washers

A:

Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when your washer has black crumbs falling out. I did look into the model number you have provided and I do apologize this unit does not have any belts. It is a direct drive so it has a motor coupling. You may be seeing the motor coupling falling apart or the tub seal. You will need to open the unit to double check. 
I have attached a photo to access the gear case. 

Let me know if this helps.

Click here to view the coupler. 
Click here to view the seal. 

 
You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
May 05, 2014
Q:

Need service manual

A:

Thank you for choosing ManageMyLife.com. I understand how important it is to be able to diagnose and repair the washer. We do not have a service manual available for this model. However, I have included instructions below on how to replace the timer in your washer. You can remove the rear panel by unscrewing the screws behind the washer.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Unplug the washer's power cord from the wall outlet.

2. Remove the two plastic end caps on the front left and right sides of the control panel. To remove, lift the top of the end cap and pull toward you.

3. Remove the screw below each end cap to release the control panel. Rotate the control panel up 180 degrees so the internal components are accessible.

4. Locate the two holes on the right side of the rear of the timer unit placed above one another. Locate the hole placed to the immediate left of the two holes.

5. Insert needle-nose pliers into the hole and pull out the long black rod inside the hole.

6. Lift the knob off the front of the timer, then remove the clear plastic piece below the knob and the dial. Simply depress the center clips.

7. Remove the two screws located below the dial on the timer.

8. Unclip the wire harness from the side of the timer from the inside of the control panel.

9. Slide the timer assembly to the left to unclip, then remove the timer assembly.

10. Insert the hooks on the right side of the new timer assembly into the grooves on the inside of the control panel, then slide the timer to the right to lock it into place.

11. Connect the wire harness to the side of the timer.

12. Connect the mounting screws to the front of the timer from the outside of the control panel.

13. Pull the black rod out of the hole on the new timer, if necessary, using the needle-nose pliers.

14. Place the dial and plastic piece back onto the timer post, then snap the timer knob back onto the timer post. Insert the black rod from the rear to secure the timer knob.

15. Rotate the control panel down and secure it with the two screws that were removed from the bottom left and right sides of the control panel.

16. Snap the plastic end-caps back onto the washer.

17. Plug the washer back into the wall or turn on the breaker.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If your washer will fill and agitate then stop, the problem may be your lid switch. If it will fill then stop, try manually advancing the timer to find out if it will complete the cycle. If the cycle completes once the timer is advanced, your timer should be replaced. If you would like more assistance, reply to this thread and please include more symptoms if possible. I would be glad to assist you further. Thanks for using ManageMyLife.com.

Read More
Lokelani -
Sears Technician
August 14, 2013

Top Parts