Model #11026901690 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Rinse cycle not filling completely 11026901690 Kenmore Super capacity plus automatic washer

Q:

how do you change the clutch 11026901690 Kenmore Super capacity plus automatic washer

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
May 13, 2014
Q:

Kenmore model 110 series 90 washer.

A:

Thank you for your question.  I am sorry you are having a problem with your Kenmore 110.26901690 Top Load Direct Drive Washer.  There is one thing I need to understand from the description you give.  If the washer will advance through the agitation cycle and stalls before it drains and spins then the lid switch may be the problem.  If the timer stalls and you manually advance it to the next cycle will the washwer run?  If you manually advance the timer and the machine will drain and spin then likely the timer  is at fault.    If you manually advance the timer but nothing happens for 15 minutes then the motor may be the problem.  You can reply below with any additional details for further assistance.  Thank you for using Manage My Life. 

Read More
Fred M -
Sears Technician
September 11, 2013
A:

Thank you for your question.  I am sorry you are having a problem with your Kenmore 110.26901690 Top Load Direct Drive Washer.  There is one thing I need to understand from the description you give.  If the washer will advance through the agitation cycle and stalls before it drains and spins then the lid switch may be the problem.  If the timer stalls and you manually advance it to the next cycle will the washwer run?  If you manually advance the timer and the machine will drain and spin then likely the timer  is at fault.    If you manually advance the timer but nothing happens for 15 minutes then the motor may be the problem.  You can reply below with any additional details for further assistance.  Thank you for using Manage My Life. 

Read More
Fred M -
Sears Technician
September 11, 2013
A:

Thanks for responding Fred. For clarification, I can manually advance timer and still nothing happens. After these symptoms first appeared, I was waiting 10 - 15 minutes and washer would restart but now absolutely nothing. Hope this clarifies some. Thanks.

Read More
Obie -
September 11, 2013
A:

Obie, from the 15 minutes I suspect the motor is the problem. A timer or lid switch problem might be intermitent but it would not be time dependent. The motor has an overload which will stop the motor and take about 10-15 m inutes to cool down and reset. The only way to verify this would be with a meter to check voltage to the motor. From the description you give I suspect the motor is the problem but a motor is not cheap and it would be nice to confirm voltage to the motor with a meter if one is available. If you have a meter or a friend with ameter then the image below may be helpful. Remember to unplug the washer before beginning.

Read More
Fred M -
Sears Technician
September 15, 2013
A:

Fred, Thanks. I did check the voltage to motor and there was none. After further investigation I discovered a bad outlet of all things. It was intermittent so that is why I felt like I was chasing rabbits but finally located the source of the problem, wasn't washer after all just a faulty outlet. Replaced outlet and all is good now. Thanks again for your input. Obie .

Read More
Obie -
September 16, 2013
A:

Glad things are working now.

Read More
Fred M -
Sears Technician
September 17, 2013
See more answers

Top Parts