Model #11026832694 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator/basket/tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I have an old Kenmore washer that works great except the water wont drain after rinse and proceed to spin. I can't find the users manual, help! Any suggestions

A:

The washer not draining can be concerning. I found some information for you that I am really hoping will help you. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you with the washer.

Read More
Marc -
November 25, 2012
A:

I know that it can be very frustrating to have issues with your washer. There are several components that will cause this to happen to the washer. These include the motor coupler, the clutch, the drive basket, or the gearcase. The motor coupler is the most common part to fail. This is a plastic part that connects the motor and the gearcase together. The image below will show you how to replace this. If this is not the case, then the clutch is the next part that will go. This video will show you how to replace this: Clutch Replacement . If these are working, then you will need to replace either the drive basket, this video will show you how to do this: Drive Basket . If all of these are working, then I would suggest you have a technician repair this. If you would like to schedule service, just click on this link: Sears Home Services . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
November 26, 2012
See more answers
Q:

fuses or circuit breaker on kenmore washing machine

A:

I know how important it is to have a good working washer in the home so that you can keep your clothes nice and clean. I suggest you add to the thread of this question and be more specific with your question about what the problem is so that the expert can provide you with a more detailed answer. I am adding the owners manual of your appliance in where you can find some good troubleshooting information. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
January 21, 2012
A:

I know that it can be very difficult to have problems with your washer. Normally there are no fuses or a circuit breaker in the washer. The power comes directly from you outlet into the wiring. If the washer is not powering on, I would suggest that you test the outlet to make sure you have power. Plug in a small lamp to test this. If this is not the problem, then you will need to test the timer, to see if it is getting power. If you are getting power and washer is not running, please reply with some more details on the problem. We will then be able to give you a more detailed answer. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
January 23, 2012
See more answers
Q:

Replace a Timer on washer

A:

A Washer is definitely something we depend and when starts malfunctioning it can be a big inconvenience. I have attached some links below well you are waiting for an expert to reply , that give great information on way this may be happening. Hope it helps!

Read More
Priscilla V -
August 08, 2011
A:

Thank you for your question and I understand your concern.

In order to remove the timer knob you must gain access to the back of the timer and pull the tab. It will have specific instructions on how to remove the knob on the back of the timer. Look on the rear of the new timer and will have instructions how to remove the timer knob.

The first step is to disconnect the power cord.

  • Remove the left and right hand end cap covers. (See image below).
  • Remove the screw located at the bottom of the left and right hand end caps.
  • Slide the control panel to you and lift it up and hinge it over the rear panel.
  • Pull the tab in the center of the shaft and then you can pull the timer knob and dial off.
  • Once you have the timer knob and dial pulled off, remove the two 5/16 hex head screws that was hidden by the timer dial.
  • Disconnect the wire harness connector from the old timer and reconnect it to the new timer and reverse the procedure to install the timer.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
August 09, 2011
A:

my end are screw on

Read More
Darrell -
November 23, 2011
A:

my end cap are screw on

Read More
Darrell -
November 23, 2011
A:

Darrell: Some models will have screws and some models have a spring clip and some will have removable end caps and then screws to remove. It just depends on the model number of your washer.

Read More
Joey S -
Sears Technician
November 23, 2011
A:

Expert Lyle provided a procedure for releasing the console in your original question. I added the link below.

Read More
Joey S -
Sears Technician
November 26, 2011
See more answers

Top Parts