Model #11026742503 KENMORE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
  • Water System Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Timer will not advance, all positions work manually, replaced timer and lid switch and still same 110.26742503

A:

Hello, glad to help.  Thank You for choosing Sears PartsDirect.com. We, at Sears, value your service.
 
I am sorry and do understand your frustration when there is problems with the washer.
 
Glad to help out.  I’m looking at your Kenmore Washer model number 110.26742503.

In providing that you have replaced the timer and lid switch correctly and that they are good.  The item that doesn't usually go bad on these is the  inline resistor kit. That will be my guess.

Inline resistor kit for the model 110.26742503.
 
Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry Jr -
Sears Technician
August 14, 2014
Q:

Gear case 11026742503 Kenmore Residential washer

A:

Thank you for choosingSearsPartsDirect.com. Knowing the oil your gearcase uses is a great question! I see here that you can use SAE 80/90 wt oil. But do not fill it to the top, it stops at the cover half level. When the oil gets warm it will expand and com out the vent and makes a mess.  I hope this helps you! Have a great day.

Read More
Samantha A -
Sears Technician
February 11, 2014
Q:

11026742503 washer not filling

A:

Our Washer is something we depend on almost daily. It is always a little frustrating when an appliance starts acting up on us. I'm sorry to hear that you are having some issues with your Kenmore Washer. I did some research at Managemylife website and found an expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. I hope this helps.

Read More
James -
February 29, 2012
A:

First of all check your water supply. make sure the valves are off, then disconnect them from the back of the washer. Then put them into a bucket and turn them back on. You should have good water flow. Before you re-connect them the washer, check the screens on the inlet couplers on your washer they need to be clean. Next unplug the washer and take the back off. Disconnect the wires to the inlet valves, they are the plastic cylinders connected to the inlet couplers you just took the hoses off of. Reconnect the hoses to the inlet couplers. You will need to put 110 volts to each pair of contacts, one valve at a time. You need to know what you are doing here so you don't get zapped. When voltage is applied water should flow into the washer. If those don't work, there's your problem, replace them (actually it is one unit) If those do work, it is most likely the water level switch. That is up in the console, it has a rubber tube connected to it and is round. Unplug the machine from the wall. Disconnect the wires from the level switch, attach an ohmeter to the contacts on the switch. Blow in the tube, it should switch on and off. If it doesn't, replace it. 0

Read More
Michael -
February 29, 2012
A:

Thank you for your question and I understand your concern.

It would be unusual for it to not fill with hot or cold water. Based on your symptom, the washer may not be filling because of a faulty water level pressure switch, timer or the water temperature switch. I added an image below of the wiring diagram and I circled the contacts in the circuit which must close in order to complete the path of voltage to the water inlet valve solenoids. If contact V and P do not close inside the water level pressure switch, the washer will fill with hot or cold water. If any of the other contacts I have circled in red do close, the washer will not fill with water. At this point in time I could not suggest any part to replace with out making some continuity checks of the contacts. If you have an Ohm meter, disconnect the water level pressure switch and place the Ohm meter leads across terminals V and P. If it does not measure continuity, replace the water level pressure switch. The washer must be empty of water before checking the continuity of contact V to P. The water temperature selector can also be tested for continuity. Be sure to disconnect the wires from the switch before testing.

In order to access the water level pressure switch, the console must be placed in the service position. You will need a putty knife to release the console clips. Slip the putty knife under the front of the control panel endcap and push back and pry that corner up, and repeat the step for the other side. Once released, lift the control panel up and hinge it over the rear panel. NOTE: Disconnect the power cord from the power source before placing the control panel in the service position. I also added a YouTube video showing how to place the control panel in the service postion . The video is focused on replacing the drain pump but of course you will not need to replace the drain pump.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
March 01, 2012
See more answers

Top Parts