Model #11026442502 KENMORE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
  • Water System Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Why won't my washer spin Kenmore 11026442502

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
January 14, 2014
Q:

Replacing lid switch in Washer

A:

Good morning.... Your question is prudent and you might as well replace it. I would suggest that you visit the website Sears Parts Direct.com. Simply enter the model number and a parts break down list, including images of the parts, will open for you to review. Also, within 10 seconds a box will open inviting you to chat with an associate who will be happy to help you locate and order whatever parts you need. I have provided a link below that will bring up a page for your particular model number. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this helps and have a nice day.

Read More
Henry -
February 04, 2013
A:

Thank you for your advice. I am at work now and lunch is ending. I will try what you suggested however.

Read More
Darrin -
February 04, 2013
A:

Thanks for the inquiry about the damaged wiring for the lid switch, I will be glad to assist.
You can get a complete wire harness for the console; however my suggestion would be to splice the connector out. Sometimes the connector can have a burn appearance but the wires are in good condition, if this is the case on yours it would not be a safety issue, but you will have to determine that.

Here is the link to Sears Parts Direct; Sears PartsDirect .

If you need additional assistance please reply and I will be happy to respond.

Ron H.

Read More
Ron H -
Sears Technician
February 05, 2013
A:

Thank you Ron. I was hoping I could just splice it as a harness is 82 bucks. Think Sears will sell just the connector as well?

Read More
Darrin -
February 05, 2013
See more answers
Q:

Kenmore elite washer

A:

Instructions to change appliance parts like this washer lid switch assembly are great help. I was able to locate a similar question that may help while you wait for the expert review and response for your model. I attached the link below. I also added Sears Home Services if you decide to schedule a technician to help. I hope this information helps with the repair project.

Read More
Barbara H. -
May 19, 2012
A:

Thanks very much. I happened to find out how on youtube and have finished already. Once again thanks.

Read More
john -
May 19, 2012
A:

Thank you for your question and I understand your concern.

The lid switch can be accessed and replaced once the control panel has been placed in the service position. Disconnect the power cord from the power source before placing the control panel in the service position.

The control panel is fastened with spring clips. The spring clips are located below the left and right hand end caps. You will need a thin putty knife to slip under the end cap. Push the putty knife under the end cap and push it inwards and pry the handle up to pop the clip and console free from the top. Repeat the step for the other side.

I added a couple of images below with the instructions.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 21, 2012
See more answers

Top Parts