Model #11022974101 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube 388952
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Water fill 11022974101 Kenmore Washer

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about your Kenmore washer model 11022974101. I am so sorry it is overflowing. I will be happy to help you with this.

There are three parts that I recommend you check to identify the issue. First check the water inlet valve. This is where the hot and cold water hoses attach to the back of the washer. Over time the valve may fail to close completely allowing too much water to enter. The second part is the water level (pressure) switch. When this part fails, the washer doesn’t know when the tub has sufficient water in it to advance to the wash cycle. The third part is the drain hose. If the water isn’t draining between cycles, too much water can accumulate in the tub causing the overflow. I have include the link below to our troubleshooting guide for additional information

Repair Guides – Washers: Overfills

If you are not comfortable checking the parts and completing the repair yourself, you can set up service at www.SearsHomeServices.com or by calling 1-800-366-7278. I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
October 18, 2014
Q:

Kenmore washer - model # 110.22974101. Makes squeaky noise on and off when in wash cycle

A:

I know that it can be very difficult to have issues with your washer. You can try to determine the source of the squeak by running the washer with the rear access panel removed. Do not make contact with any internal components when running the washer with that panel removed. If the squeak is coming from the rear tub bearing, then you may eventually need to replace that bearing. If the belt is slipping and squeaking, then you will probably need to replace that belt. You may find that the squeak is caused by a different component. If you could please reply with this information, I can then provide a more detailed answer. If you don't feel comfortable doing this yourself, please click on the link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using ManageMyLife.com.

Read More
AnneJ -
Sears Technician
September 11, 2013
A:

Thank you for the reply. Would you please be more specific - "Do not make contact with any internal components when running the washer with that panel removed." After removing the rear access panel, I should run the washer - start the wash cycle without any clothes? And do not touch the inside of the washer while it is "washing". If I'm understanding correctly, I can do this on my own and then report back my findings.

Read More
Vanessa -
September 11, 2013
A:

My understanding is there is no belt on this washer model.

Read More
Vanessa -
September 11, 2013
A:

Yes you will start the washer will not clothes in it, and the panel off. This way you can see into the internal componets. Do not touch anything while the unit is running. That would be very dangerous. Once you have idenified the source, please let me know so we can help you get it fixed.

Read More
AnneJ -
Sears Technician
September 11, 2013
See more answers
Q:

Washer, model #110.22974101. Clothes coming out wet after spin cycle.

A:

When an appliance suddenly stops working it can cause an inconvenience in your home. While you are waiting for an expert to respond I was able to locate some great information that could possibly assist you with your issue. I have added the link below. Hope this helps!

Read More
Yadira B -
February 07, 2013
A:

Thanks for the information about your washer not spinning the clothes dry enough; I will be glad to help with this.

Based on the information provided, I will suggest that you closely inspect the drain hose behind the washer for kinks or partial clogs. Be sure the hose has not been extended to a length of more than 96 inches. Next sometimes a small piece of clothing can get out of the inner tub and block the sump hose leading to the pump (check at tub and pump) also look closely inside the washer with a bright light for obstructions between tubs.

If all the hosed are okay then I would suspect a spin speed problem generally caused by the Brake and drive tube and the clutch assembly, this is a major repair and I would strongly consider repair vs. replace.

I hope this helps, if we can be of further assistance please reply with details and I will be happy to respond.

Ron H.
If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Ron H -
Sears Technician
February 07, 2013
A:

Thank you for the reply! I will check the drain hose. Upon greater inspection, it seems when the washer is in spin cycle, it is not spinning fast enough. I held down the lid switch to see the movement during the spin cycle. The spin cycle stops almost immediately when the lid is opened. This must be the spin speed problem you described. The solution to this is to replace the Brake + drive tube + clutch, all 3 parts? I went to a local appliance supply and the guy mentioned that it was probably the clutch. What do you mean by repair vs. replace? Clutch assembly, consists of what? Sears has the Clutch that comes with spring and cap. The Clutch Band kit is separately, would I need this too? Thank you!

Read More
Vanessa -
February 08, 2013
A:

Just to update - I first replaced the pump. But turned out, the pump wasn't the problem. The new pump worked the same as the old one. After reading the suggestions here, next I replaced the clutch. And the washer worked beautifully. Thank you for the suggestions.

Read More
Vanessa -
September 10, 2013
See more answers

Top Parts