Model #11022912101 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube 388952
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

washer doesn't refill after 1st wash cycle

A:

I did some research on the unit and I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within two business days with detailed information. Thank you for using Manage My Life.

Read More
Joseph P. -
July 17, 2013
A:

Thank you for your question and I understand your concern.

When it fails to fill in the rinse cycle, push the timer in and rotated around back to the wash cycle and pull the knob back at and see if will fill. If it does, I suspect a faulty timer.

Generally speaking, it should never begin agitating until the water level pressure switch is satisfied. Now, if for some reason the water level pressure switch fails to reset after the water has drained, it will begin agitating without any water in the washer. This is why I suggest pushing the timer in and rotating the timer around to the beginning of the wash cycle again when you find it agitating in the rinse cycle without any water in the tub.

If it begins filling when take the timer back to the wash cycle, I would suspect a faulty timer.

Just for you information, there is one spot on the timer near the end of the wash cycle indicated by a * that will cause it to begin agitating without any water in the tub. This spot is used just to test the agitation action without having to wait for it to fill and satisfy the water level pressure switch. If you happen to start it at the (*) mark, you will see it "dry agitate".  

  I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.


Read More
Joey S -
Sears Technician
July 19, 2013
See more answers
Q:

110-22912101 WASHER FILLS AND AGITATES BUT WLL NOT EMPTY OR SPIN 110-22912 101

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Yadira B -
June 09, 2013
A:

I know that it can be very frustrating to have issues with your washer. You did not indicate if the motor is running during the drain or spin cycle. I'm going to assume that the motor only runs during the agitate cycles only. Most likely the safety lid switch or the lid switch actuator is broken. If the lid switch is not being energized and closed when the lid is shut the motor is not going to run at all during spin and drain cycles. Check under the bottom of the lid to confirm that the lid strike is still attached to the lid. Open the lid and look down the little opening where the lid strike would insert into to trip the lid switch to see if the actuator is broken. In order to gain access the lid switch to replace it the washer cabinet must be removed. The image below will provide these instructions for you. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 10, 2013
See more answers
Q:

Washer will not agitate

A:

Washers are appliances we count on daily to help us keep up with nice and clean clothes> While you are waiting on an expert to answer your question, I found some great links in the Manage My Life website. I have attached the links below. Hope this helps!

Read More
Dezeray S -
March 28, 2012
A:

Hi Eli,

Thank you for submitting a question to Manage My Life.

This is most likely a timer issue. The start winding starts both agitate and spin, but the timer may not send voltage correctly during the start of agitate. The diagnosis of this issue will require the use of a volt/ohm meter. If you have a meter and are confident in your technical abilities please reply below and I will be happy to assist you further. I am including an image below that explains what happens in your washer during agitation.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website; Sears Home Services .

I hope this is helpful. If I may be of further assistance please include more details in a reply to this post.

Landell

Read More
Landell -
Sears Technician
March 28, 2012
A:

Landell, Thanks for your advice. I have a volt/ohm meter and am prepared to proceed. Regards, Eli

Read More
Anonymous -
March 28, 2012
A:

Hi Eli,

I am including the esterline timer chart in the image below. This chart shows which contacts are closed in each function. When the motor starts agitation you should have voltage red to yellow to the start winding and blue to white for agitation.

I hope this is helpful. Check the things I have covered here and if I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
March 29, 2012
See more answers

Top Parts