Model #11022894101 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube 388952
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My Series 80 washing machine works great until it's supposed to drain. Then it does nothing. What is your best guess?

A:

When I am having trouble with my washing machine what I always do is visit the Sears Home Service website for very useful troubleshooting information. I have attached the link below if you are interested in viewing the website while waiting for a response from an expert. Hope this helps!

Read More
Alina F. -
July 08, 2010
A:

From the description you give the problem is most likely with the lid switch.

This washer can fill and agitate with a bad lid switch but it can't drain or spin with a bad lid switch.

I'd suggest you first access and check the lid switch. The switch might be broke or the strike may be broken.

The image below will show you how to raise the console and remove the cabinet to access the lid switch. The switch can even be bypassed for a moment to see if it is the cause of this problem.

Remember to unplug the washer first.

The lid switch can be obtained from the following link: Sears PartsDirect .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Mark T Personal Solutions Manager -
Sears Technician
July 12, 2010
See more answers
Q:

I have a Kenmore Model 110.22894.101 and need to replace the lid switch, Model 3949238. How best to do this???

A:

The image below will show you how to raise the console and remove the cabinet to access the lid switch.

Remember to unplug the washer first.

Your particular washer has two end caps that must be removed to access the two screws holding the console down.

I hope this information is helpful to you but submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
May 15, 2010
Q:

What is the procedure for removing and replacing the lid switch?

A:

In order to access and replace the lid switch will require removing the washer cabinet and not the rear panel.

To access the lid switch the washer cabinet will need to be removed. See images below.

  • First, disconnect the power cord from the power source.

  • The console (key#26) will need to be placed in the service position by removing two (2) hidden screws, one (1) screw is located at the bottom of the left hand end cap (key#7) and one (1) screw is located at the bottom of the right hand end cap (key#10).

  • In order to access these two (2) hidden screws, the left hand end cap trim (key#8) and under the right hand end cap trim (key#15) will need to be removed.

  • To remove the trim (key#8&15), place you finger behind the trim at the very top and bend it up enough to clear the console and then hinge it towards the front and off.

  • Remove the hidden screw under each end cap trim. Slide the console forwards about 1/4 inch and the raise it upwards and hinge it over the rear panel.

  • Disconnect the 3 wire lid switch harness plug located on the top. Pop the two (2) gold colored cabinet retainer clips off.

  • Place the tip of a flat tipped screw driver down into the first valley and then push the handle end to the rear of the washer to pop off the cabinet clips.

  • Open the lid and grab the opening and tilt the top of the washer cabinet forwards just a few degrees and then walk it backwards and off.

  • The lid switch mounted under the main top is now accessible to remove and replace.

Reverse the procedure to re-assemble the washer.

Read More
Joey S -
Sears Technician
September 18, 2009

Top Parts