Model #11022862100 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube 388952
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Timer knob

A:

Thank you for your question. I will give you the removal information because this is how I have it in my mind. You will reverse this information to install. There are 2 possibilities of how the timer knob comes off. Look closely on the back of the knob where the shaft goes. If there are threads in the opening you hold the outer ring of the timer dial and turn the inner part counter clockwise to unscrew it.

If the hole in the knob doesn't have screws you release the knob from the back of the timer. Unplug the washer from the wall outlet.

On each end of the console is a piece of trim you must remove. Place your fingers on the console with the back of the tips touching the trim. Put some pressure on the console and it will give enough to let you pry out with your fingers. When it snaps out roll the trim toward the outside edge of the console and the trim will come off.

  • Remove the two phillips screws at the top of the console and it will pull forward from the top.
  • On the back of the timer are the directions for removing and installing the knob.
  • Push the timer knob in. With a small screwdriver apply some pressure to the small part in the center of the shaft to hold it back while you pull the knob off.
  • Pull the timer shaft out and push the center portion back firmly; it will stay back.
  • Align the knob with the shaft and push it on.
Reverse these directions to reassemble the console and trim.

The instructions on the back of the timer will tell you the same thing I did.

Reply to this post with more questions.

Thank you for choosing
Manage My Life.

Read More
dtova00 -
Sears Technician
September 10, 2013
A:

This was not the answer I wanted. After a few days of no response, I figured out the problem myself. When I removed the knob initially I put it back on but in a different cycle than when I took it off. When I started the washer the knob was in the permanent press position but ran in the utra clean cycle. After watching and timing the cycle, I adjusted the knob to the correct position. Thank you very much for your effort in trying to help. I will surely call on managemylife if another problem arises. Thank you again

Read More
michael -
September 11, 2013
See more answers
Q:

I have a Kenmore washer leaking water when the basket is drained

A:

I'm sorry about the difficulties that you are experiencing with your Kenmore washer. I did some research at Managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond to your specific question. I have attached the link below. If you decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
April 20, 2011
A:

Thank you for your question and I understand your concern.

Without being there to check the washer myself it will be hard for me to say where the water leak is emitting from. It could be from the drain hose or drain pump. In order to locate the leak the washer cabinet will need to be taken off the base.

I added a YouTube video show how to access and replace the pump. If the water appears to leak from the front center area then it's likely a leaking drain pump. Note: Disconnect the power cord before servicing your washer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 21, 2011
See more answers
Q:

My Kenmore washer (Model # 11022862100) will fill with water but will not go through any of the cycles.

A:

I understand how important it is to have a good working washer in your home since dirty clothes do tend to gather quickly. While you are waiting for an expert to answer your question, I was searching in the Manage My Life website and found some great links. You can also visit Sears Home Services website to set service with a Sears technician. I have provided the links below. Hope this helps!

Read More
Dezeray S -
April 12, 2011
A:

From the description you give the problem can be the water level switch, timer or even motor.

It's odd for the water level switch to fail and not flood the house but I suggest you start here.

The easiest way to check if this is the problem is with a small piece or insulated wire. With the washer unplugged remove the violet and tan wires from the water level switch. Use the small piece of insulated wire to join the violet and tan wire without touching anything metal.

Carefully plug the washer in and see if it will agitate. If it does then you have found the problem. If it still does nothing then the timer or motor is the problem.

Give me a reply with what happens and we'll continue from there.

Read More
Fred M -
Sears Technician
April 13, 2011
See more answers

Top Parts