Model #11022832100 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator,basket, And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube 388952
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

washing machine leaking

A:

Thank you for your question and I understand your concern.

If the water leak appears to emitting from the front center area under the washer, the drain pump is likely leaking and will need to be replaced.

Also, if the tub and basket is leaning forwards after loading the clothes, when water begins to enter the washer, the water can hit the top of the tub cover and then leak down onto the floor.

The leak could also be emitting from the tub to drain pump hose or from the drain hose under the washer or on the outside of the washer. I have also seen water back up and out the top of the stand pipe where the drain hose is stuck in too.

In order to have full access to the drain pump and hoses, the washer cabinet will need to take off the base.

NOTE: Disconnect the power cord from the power source before removing the cabinet. 

To remove the washer cabinet, the left and right control panel end cap covers must be taken off. Lift the upper back portion of the end cap covers up in order to clear the end cap and pivot the top of the end cap cover towards the front of the washer and remove. Remove the screw located at the bottom of each control panel end cap. Slide the control panel towards the front of the washer and then lift it up and hinge it over the back panel. Disconnect the lid switch harness connector from the top of the washer. Pry the two gold colored cabinet retainer clips off securing the top of the cabinet to the rear panel. Open the lid and lean the top of the cabinet towards the front of the washer and walk it straight out away from the washer. You now have access to inspect for the leak. You plug the washer in and then start a wash cycle and watch for the leak. NOTE: The washer will not operate in the drain and spin cycles with the lid switch harness connector disconnected.

I added a couple of images below to reference the instructions for removing the end cap covers and cabinet.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 06, 2013
Q:

Kenmore 80 series model 110.22832100 is not spinning.

A:

It can be challenging to find issues like this. The expert will review the work done to help. I did locate a similar question that may provide some help. I attached to a link below along with one for a technician if needed.

Read More
Barbara -
March 10, 2013
A:

I know that it can be very difficult to have issues with your washer. The basket not spinning is likely caused by the clutch and/or basket drive. Two things to try first. After the water drains out turn the washer off and then back on and see if it starts to spin. If it does then it is a neutral drain problem and the timer needs to be replaced. Next try and give the basket a push start in spin. If it starts to spin then likely the clutch and basket drive need to be replaced. The images below will give you an idea how to access the clutch. Remember to unplug the washer first. I'm not clear on which part you're looking for. Between the motor and clutch is the transmission. Check this parts image and see if you can find the part: Kenmore Model 110.27812690 Washer . If you don't feel comfortable doing this yourself, just click on this link to schedule service: SearsHomeServices.com . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
March 11, 2013
See more answers
Q:

Our washer is overflowing

A:

Having your washer fail to operate properly can be very aggravating. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Your expert will answer within 24 to 48 hours with detailed information. Thank you for using Manage My Life.

Read More
Julio -
February 01, 2013
A:

Thank you for your question. I have answered this question from your previous post and it can be viewed on this link; What causes overflow of washer tub? . If there are additional questions, feel free to reply on either thread. I will be happy to help.

Read More
Barbara H. -
Sears Technician
February 03, 2013
See more answers

Top Parts