Model #11022084100 KENMORE ELITE Residential Washers

  • Top And Lid
    3 Results
  • Cabinet And Frame
    3 Results
  • Washplate, Basket And Tub
    3 Results
  • Control Panel
    3 Results
  • Brake, Motor And Pump
    3 Results
  • Suspension
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube
    3 Results
Find part by diagram >

Question and Answers

Q:

replace washplate 11022084100 Kenmore Elite Washer

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.







You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 27, 2015
Q:

Hello, I have a Kenmore Elite Calypso motion that is leaking from the bottom.

A:

I am sorry that you are having problems with your washer. I suggest you add to the thread of this question and include the full model number of your washer so that the expert can provide you with a more detailed answer. I am adding a link below to help you locate the model number. I hope this helps with your research while you wait for your expert response. 

Read More
Joseph P. -
March 14, 2013
A:

Kenmore Elite model # 110.22084100

Read More
Marten -
March 14, 2013
A:

Have I provided enough information? When can I expect to hear from an expert? Thank you, Marten

Read More
Marten -
March 14, 2013
A:

Thank you for your question and I understand your concern.

 I added an image below showing how raise the top and and how to remove the front panel so you can search for the leak.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
March 15, 2013
A:

Hello Joey S. Thank you for your help. I was able to open the washer and see where the leak was. It was the hose coming from the pump. It appeared that the wrong hose was on the washer. Who ever serviced it (We bought it used) cut some corners and installed a hose that was a lot longer than the factory. It kinked and leaked. I ordered the correct hose that was 1/2 as long, installed it and all is well. Thank you for your help. With out your expertise I would have paid over $125.00 for a service tech to diagnose and fix the issue. With your help I fixed it for $30.00! :-)

Read More
Marten -
March 20, 2013
A:

Marten: I'm happy you were able to locate and resolve the leak. Thankyou for using Manage My Life.

Read More
Joey S -
Sears Technician
March 20, 2013
See more answers
Q:

Kenmore Elite Calypso - How is it possible for the spanner nut to be outside of the inner wash plate and for the washer to still work?

A:

It seems as if this washer is giving you a bit of a headache. It is frustrating when you have to deal with an appliance that causes so much trouble. While you wait for an expert to respond, I have attached a couple links below that provide information on the OB error code. I hope all goes well.

Read More
Jackie S -
March 26, 2012
A:

Here is a photo of the spanner nut...

Read More
David -
March 26, 2012
A:

That spanner nut secures the U-joint to the drive block. The basic theory of operation for the nutation is shown in the first image below. The other 3 images show the service procedure for that drive system. You have probably already seen that procedure according to your details. Be sure that you unplug the washer before accessing internal components. You will normally have to lift your spanner wrench up slightly when tightening down that new spanner nut to keep from bottoming out on the U-joint.

If you decide to repair this problem, you can order parts from this page: Kenmore Elite Calypso Washer 110.22084100 Parts .

My personal recommendation is that you examine the washer and determine the parts that you will need before you decide to repair this washer. The U-joint kit alone is close to $200. You may need other parts as well. Even if you repair this failure in the drive system, you may have other failures fairly soon based on the age of the washer. In most situations, it will be more economical to replace the Calypso washer instead of repairing it.

If you decide to replace the washer, you can view current models of washing machines on the Sears.com website.

Reply with additional details if you need more help.

Read More
Lyle W -
Sears Technician
March 27, 2012
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
March 27, 2012
A:

Lyle - Thank you for the diagrams and the tip on how to install the spanner nut. Before I order the parts, which as you say may make the repair too expensive, I would really like to understand what I am up against. The only spanner nut that I found inside the machine was in the bottom of the basket and completely corroded (see photo). There was no second spanner nut under the inner wash plate which had been bolted down. Why didn't the u-joint fall off the drive block? All the parts under the inner wash plate seemed normal, except the missing spanner nut. Also, on the Sears Direct website, the spanner nut wrench (14218862) is not available. Where can I buy a similar tool so that I can install the new parts? Thanks in advance, David

Read More
David -
March 28, 2012
A:

I looked at that photo and it appears to be a spanner nut at first glance but it is very corroded. There is a possibility that is a different component. If you found that part in the bottom of the spin basket before you took off that inner wash plate off, then that is probably not a spanner nut from the Calypso washer. Without being able to physically examine the washer, I don't think that I will be able to determine exactly where that part came from. Here is a link for a page that shows the spanner nut that you should find on that Calypso washer: Spanner Nut for Kenmore Elite Calypso Washer 110.22084100 . This information may help you determine whether that item at the bottom of the spin basket was the spanner nut. If it does not match, then you should find that spanner nut on the top of the drive block as shown in that second image. If you decide to repair the washer and you need a spanner wrench (part 14218862), then you can order it from a website such as Repair Clinic or you can perform a web search using Google or a similar search engine. I provided a link for that spanner wrench on Repair Clinic.com below this response. I hope that this additional information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
March 28, 2012
A:

Lyle - Thanks for reviewing the photo. Now that I have the new spanner nut, I can see that the pieces that have been sliding around in my washer for years are not from my washer. The actual spanner nut is much smaller and still on the machine. I bought the spanner nut wrench at repair clinic.com (thank you for the link). However, the spanner nut seems to be on real tight. Is there a trick to loosening the nut? Do you need to block the u-joint? Is it OK to use penetrants to help loosen the nut? I tried tapping the spanner nut wrench with a rubber mallet as illustrated and it won't budge. Thanks, David

Read More
David -
April 02, 2012
A:

You can use some penetrans to help loosen that spanner nut. Let them soak in for at least a couple of hours. There is not really any other trick other than using the penetrants to loosen that nut. That spanner nut may have residue and corrosion built up on the threads. That will prevent it from breaking free. Brute force will normally be needed to break that spanner nut loose.

Read More
Lyle W -
Sears Technician
April 02, 2012
See more answers

Top Parts