Model #11022066100 KENMORE ELITE Residential Washers

  • Top And Lid
    3 Results
  • Cabinet And Frame
    3 Results
  • Washplate, Basket And Tub
    3 Results
  • Control Panel
    3 Results
  • Brake, Motor And Pump
    3 Results
  • Suspension
    3 Results
  • Miscelleous
    3 Results
  • Brake And Drive Tube
    3 Results
Find part by diagram >

Question and Answers

Q:

won't complete cycle 11022066100 Kenmore Elite Washer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your washer is not working properly.



Key Dance: PREWASH OPTIONS ⇒ WASH TIME ⇒PREWASH OPTIONS ⇒ WASH TIME
 
The Automatic Service Diagnostics Test is activated.
Key Dance must be completed within 5 seconds to be valid.

If the diagnostics does not bring up any error codes you will need to have the unit diagnosed by a service technicain. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
November 29, 2014
Q:

I have a Calypso washer, model 11022066100. It stopped with an error code LD..

A:

Its' frustrating to have problems with the Calypso washer, but good to see there is a place to go for answers. Below is a link with helpful information on the error code LD, on another washer. Hope this helps while waiting for additional information on your specific model.

Read More
Anna T -
August 05, 2012
A:

I suspect there is a problem with the pressure switch or air trap. The LD error code stands for long drain.

You didn't say the water drains okay.

The control is looking at the pressure switch to bring up the LD error. Even if the water is draining out if the pressure switch doesn't reflect the water draining out then the control will assume there is no drain.

For this problem I'd suggest you raise the console and access the operating pressure switch. Remember to unplug the washer first. With the washer empty remove the plastic hose from the pressure switch. It should have no kinks or twists. Try blowing through the hose towards the tub. You should be able to blow freely without to much effort.

If you can't blow then there is a kink or blockage in the air trap. If you can blow through the hose then try reattaching it and try another cycle and see if there is any improvement.

The images below may help with this problem.

Remember to unplug the washer first.

Read More
Jerome G. - Personal Solutions Manager -
Sears Technician
August 06, 2012
A:

I fixed the unit by removal of a softner sheet stuck in the pump. Softner sheets can stick inside clothing undetected and end up in the washer. They have very strong fibers and do not shred when exposed to water. All it took was one sheet and it jammed the pump impellar. That's a few hundred dollars saved by not listening to experts!

Read More
robin248 -
August 07, 2012
See more answers
Q:

What can I do to prevent my washer from leaving grease on my clothes?

A:

The grease is most likely coming from the u-joint assembly. In order to solve grease from getting on the clothes the u-joint assembly will need to be replaced. This can be a major procedure to say the least and I highly recommend calling a service technician to remove and replace the u-joint assembly.

I recommend calling a service technician to diagnose and repair your washer.

Read More
Joey S -
Sears Technician
July 28, 2008
A:

Several things took place at the same time that my washer started leaving grease on my clothes. First the faucet was replaced. Then washers were added so that the nozzle on the faucet would be long enough so that the washer could be hooked up to the faucet. Then when I washed clothes the very next time there was grease on clother that was in every load. Do you have any idea as to what may have caused the problem with the grease? And what do I need to do to get it fixed? Or would be so expensive to fix it that it is not worth it and would it be more to my advantage just to replace the washer?

Read More
Loretta -
March 09, 2012
A:

Loretta: If you have a Kenmore Calypso washer; I suggest replacing it rather than having it repaired. The grease is most likely emitting from the u-joint assembly. This repair can wind up costing more than the cost of new washer.

Read More
Joey S -
Sears Technician
April 17, 2012
See more answers

Top Parts