Model #11020922991 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube 388952
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Water runs in during spin cycle 11020922990 Kenmore Automatic washer

A:

I understand that your washer is spinning and at the same time is dispensing water. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
May 24, 2013
A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. The issue you're experiencing will either be with the water mixing valve, water level switch or pressure hose. I believe the issue is with the water valve. I recommend testing the water valve with an ohms/volt meter, so you'll know if the the water valve  has the proper continuity. If the valve is good, then I recommend checking the pressure switch hose. See if the hose is damaged in any way. You can blow into the pressure hose to make sure it's clear. The pressure hose is attached to the base of the water level switch. If it's good, then replace the water level switch. The image below will help you open the control panel and cabinet to access these parts. You can order parts from our Sears Parts Direct web site. I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
May 24, 2013
See more answers
Q:

MODEL 110.20922991 SEARS WASHER

A:

I can definitely understand your concern over wanting to obtain the wiring diagram for your washer. I did some research and provided a link to a similar question and answer on our site. I hope this will give you a better idea on the next step to take until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
December 03, 2012
A:

The key in the description is your statement, "water did not shut off." If the water would not shut off even when the washer was turned off then the problem is the water valve stuck in the open position. This can be an intermittent problem. If the water kept filling even with the washer turned off and you had to turn the water supply spigot off to stop the water then replace the water valve. The wiring diagram below may be helpful. The water level switch is circled. The switch can fail but usually will fail consistently. There is a clear plastic hose that connects the water level switch to the air dome on the side of the outer tub. If this hose is kinked or has a hole then the washer would overfill. I hope this helps. You can reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
December 04, 2012
See more answers
Q:

Name's Jim I have a Kenmore washer model #110.20922991. & I need a wiring diagram for this model. The washer overfilled with water. Please help.

A:

Having a working washer is a necessity. I did some research on your model number but was not able to find a wiring diagram. Your expert will be able to help answer your question. It may take 24-48 hours. I do hope everything works out with the washer.

Read More
Marc -
November 30, 2012
A:

If the washer overfilled during a cycle then the water level switch is the most likely cause of the problem. The water level switch circuit is circled in the image below. The water level switch has a clear plastic hose that delivers air pressure from the air dome on the side of the tub to the water level switch. If the air dome is clogged or if the hose is kinked or has a small pin hole then the washer would overfill. I would suggest checking the hose first. The image below will help you remove the cabinet to check the hose. Remember to unplug the washer first.

Read More
Fred M -
Sears Technician
December 01, 2012
A:

Thanks !! At least now I know where to start. The overflow occurred 1X only then machine ran fine the next 5 cycles ~ but I don't trust it anymore. -Jim-

Read More
JIM -
December 03, 2012
A:

Just remember not to run the washer and leave the house. It will most likely fail again at the worst possible moment. Murphy's Law.

Read More
Fred M -
Sears Technician
December 04, 2012
See more answers

Top Parts