Model #11020904990 KENMORE Residential Washers

  • Top And Console
    3 Results
  • Rear Panel
    3 Results
  • Agitator/basket/tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

wont spin 11020904990 Kenmore Automatic washer

Q:

Water level 11020904990 Kenmore Automatic washer

A:

Thank you for your question and I understand your concern.
 
NOTE: You submitted this question twice and I added the wrong link for the water level pressure switch in my first response. Use the links below for the correct part links. 

If the water will stop filling when you push the timer knob in or if you unplug the washer; I suspect a faulty water level pressure switch part number W10337780. If you have to turn the water supply valve(s) off because turning off the washer or disconnecting the power cord does not shut the water off, then I suspect the water inlet valve assembly part  number 285805 is faulty and will need to be replaced.

The is also a small air hose connected between the water level pressure switch and the air dome on the lower side of the tub that could be leaking air or it could become restricted at the nipple of the air dome. 

In order to access the water level pressure switch, the control panel must be placed in the service position.  To place the control panel in the service position, disconnect the power cord from the power source first. 

Remove the left and right end cap covers from the ends of the control panel. To remove the end cap covers' grasp the top rear lip of the end cap covers and lift it up to clear the end cap and hinge it towards the front of the washer. See image below. After removing the left and right hand end cap covers, remove the screw located at the bottom of the left and right hand end cap. After removing the two screws, slide the control panel towards the front of the washer 1/2 inch and then lift the control panel up and hinge it over the rear panel.

Remove the air hose from the pressure switch and blow into and to make sure it is clear.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
September 24, 2013
Q:

Water level 11020904990 Kenmore Automatic washer

A:

Thank you for your question and I understand your concern.

If the water will stop filling when you push the timer knob in or if you unplug the washer; I suspect a faulty water level pressure switch. If you have to turn the water supply valve(s) off because turning off the washer or disconnecting the power cord does not shut the water off, then I suspect the water inlet valve assembly part #W10337780 is faulty and will need to be replaced.

The is also a small air hose connected between the water level pressure switch and the air dome on the lower side of the tub that could be leaking air or it could become restricted at the nipple on the air dome where the air hose connects.

In order to access the water level pressure switch, the control panel must be placed in the service position.  To place the control panel in the service position, disconnect the power cord from the power source first. 

Remove the left and right end cap covers from the ends of the control panel. To remove the end cap covers' grasp the top rear lip of the end cap covers and lift it up to clear the end cap and hinge it towards the front of the washer. See image below. After removing the left and right hand end cap covers, remove the screw located at the bottom of the left and right hand end cap. After removing the two screws, slide the control panel towards the front of the washer 1/2 inch and then lift the control panel up and hinge it over the rear panel.

Remove the air hose from the pressure switch and blow into and to make sure it is clear.

 

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.


Read More
Joey S -
Sears Technician
September 24, 2013

Top Parts