Model #11020901990 KENMORE Residential Washers

  • Top And Console
    3 Results
  • Rear Panel
    3 Results
  • Agitator/basket/tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

machine will not stop filling 11020901990 Kenmore Automatic washer

A:

Thank You for contacting SearsPartsDirect.com. I do apologize for the delay in answering your question.
If the washer won't stop the water from filling then it can be a number of problems.

You didn't provide a lot of detail. One thing is does the washer stop filling when it is turned off or even unplugged? If it continues to fill then most likely it is a bad water valve causing this problem.

The water level switch on this machine only has two wires. The switch is open (filling) or close (filled) and is located in the console.

Another possibility is the drain hose might be to far down the standpipe causing a siphon action. The washer would fill and drain at the same time. It wouldn't flood the room but it wouldn't stop filling either.

If you need further assistance, please resubmit your question with additional details. Thanks for visiting SearsPartsDirect.com

Read More
Desirea -
Sears Technician
March 22, 2014
Q:

control panel 11020901990 Kenmore Automatic washer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Barbara -
July 28, 2013
A:

I understand how important it is to be able to properly disassemble your washing machine. Although I was unable to specifically find the disassembly process for this particular model, I have included below general instructions on how to remove the cabinet for a top loading washer.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Remove the console. Use a screwdriver to remove the two screws on the ends of the front of the console. Locate the four screws that attach the console in the back and remove them as well.

2. Lift the console from the washer and let it rest behind the machine. Do not let the wires become over-stressed.

3. Remove the two brass clips where the console was attached. Insert a screwdriver between the top of the washer and the clip. Lift up and toward the rear of the washer to release the clips.

4. Disconnect the lid switch connector plug from the washer. It is located on the top of the washer where the console was located; it looks like white casing.

5. Lift the washer lid and get a grip between the tub and the cabinet frame. Tilt the cabinet toward you, then back to the wall to disconnect it from the bottom.

6. Lift the entire cabinet over the tub and place it out of the way.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services

Thank you for using Manage My Life.

Read More
Desiree -
Sears Technician
July 30, 2013
See more answers
Q:

cabinet removal 11020901990 Kenmore Automatic washer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Barbara -
July 28, 2013
A:

Thank you for choosing SearsPartsDirect.com. I understand how important it is to be able to properly disassemble your washing machine. Although I was unable to specifically find the disassembly process for this particular model, I have included below general instructions on how to remove the cabinet for a top loading washer.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Remove the console. Use a screwdriver to remove the two screws on the ends of the front of the console. Locate the four screws that attach the console in the back and remove them as well.

2. Lift the console from the washer and let it rest behind the machine. Do not let the wires become over-stressed.

3. Remove the two brass clips where the console was attached. Insert a screwdriver between the top of the washer and the clip. Lift up and toward the rear of the washer to release the clips.

4. Disconnect the lid switch connector plug from the washer. It is located on the top of the washer where the console was located; it looks like white casing.

5. Lift the washer lid and get a grip between the tub and the cabinet frame. Tilt the cabinet toward you, then back to the wall to disconnect it from the bottom.

6. Lift the entire cabinet over the tub and place it out of the way.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If you have further questions please let me know. Thanks for using SearsPartsDirect.com.

Read More
Lokelani -
Sears Technician
July 29, 2013
See more answers

Top Parts