Model #11020872990 KENMORE Residential Washers

  • Top And Console
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is the capacity of my Sears Kenmore Series 80 washer model number 110.20872990 ? 110.20872990

A:

Thank you for choosing Sears Parts Direct. I can certainly understand how you would want to know the capacity of your Washer. I did look into the model number you have provided and I have found that your unit is 3.0 cu. Ft.

 Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
October 17, 2013
A:

Hi- I'm trying to find out the amount of gallons of water that is used per each water level selection on the Kenmore 110020872990 80 series washer. thank you

Read More
Rita -
October 31, 2015
See more answers
Q:

Washer model #11020872990 won't advance at the end of the wash cycle. 11020872990

A:

Thank you for your inquiry on your Kenmore Washer, Model: 110.20872990. From reviewing the details on your model,from what you’re describing it sounds like the lid switch, timer or wiring harness has problems. Open and close the lid slowly and listen carefully for the click of the lid switch. If the lid switch is not clicking, you will need to replace the lid switch. If the lid switch checks well I recommend checking the timer harness plug-in connector & removing the cabinet to check the motor harness plug-in connector. Other testing will require using a meter.

Safety Warning: Before beginning the repair, disconnect the direct power supply to the washer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

 

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
June 02, 2015
Q:

Washer makes loud bearing-like noise at very beginning of spin cycle, then goes away after about 5 to 10 seconds 11020872990 Kenmore Automatic washer

A:

I would like to add there has been no burning smell. And no sounds like a belt slipping. None of the other cycles makes any strange noises. And something else I've noticed is that way smaller loads make less noise.

Read More
Phil -
February 01, 2015
A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your washer and I do understand your frustration. Glad to help out. I'm looking at your model number 11020872990 and from your description I would suspect that the drain pump is the cause of the sound. The drain pump will work for a few seconds as the basket begin to drain and spin. I recommend checking the pump and the motor. If a bearing is bad typical the noise will remain throughout the cycle. Here is a link that will help with additional troubleshooting. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
February 04, 2015
A:

Hi Mr. Wallace, thanks for responding. None of those videos sound like what I am hearing. Is there some way I can upload a recording of the sound, or a video for you to listen to? If it is the drain pump, is the part cheap enough and easy enough to replace that it would be worth doing, or would I be better off putting that money into a new washer? Thanks again ... Phil

Read More
Phil -
February 08, 2015
See more answers

Top Parts