Model #11012502100 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Washing machine won't restart after opening and closing lid

A:

Further to the original post above: I just noticed my repair parts list is for a different model of machine: 110.12502100. Are the part numbers in this part list valid for my model which is 110.24652300? Are there any instructions for how to disassemble the laundry machine to access the lid switch?

Read More
Dan -
September 28, 2013
A:

Further to the above posts: After emptying the wash basin/tub, I discovered the basin will refill automatically. However, once filled the cycle stops and does not continue. It will not agitate or drain. So does not appear to be a lid switch issue after all.

Read More
Dan -
September 28, 2013
A:

Doing some searching on the site, looks like might be the lid switch after all. Will try to access the switch based on some instructions for other machines.

Read More
Dan -
September 28, 2013
A:

Problem solved. The lid switch unit had separated. Possibly the glue holding switch together dried out and failed. I placed a small C-clamp on the switch to hold it together, and now it works fine. For future reference, the lid switch model number printed on the unit is 3949238. Other numbers printed on the switch include 10800-B1 and 0323D.

Read More
Dan -
September 28, 2013
A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. If you're like to test the lid switch to verify the part, the switch can be checked two ways. The first way is with a volt/ohm meter and you can check continuity across the two terminals on the switch. The circuit should show open and closed as the lid is open and closed. If you have no meter then the lid switch can be bypassed to see if it is the problem. The idea is to remove both of the wires from the lid switch and join (jump) them together with a small wire. With the lid switch bypassed you can see if the washer will drain and spin. The image below shows how to remove the cabinet to access the lid switch but look at the bottom of the instructions to see how to bypass the lid switch. Remember to unplug the washer before performing any test or repair. You can order parts from our Sears Parts Direct web site. I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
September 30, 2013
See more answers
Q:

My Kenmore model #11012502100 will not spin.

A:

The washer not spinning can leave your clothes very wet at the end of the cycle and take a very long time to dry. I am sorry for the inconvenience and I did manage to find a link that will provide you with some good information. I hope this helps with the spin problem, while you wait for your expert response.

Read More
Joseph P. -
June 23, 2012
A:

It sounds like the motor is not getting the correct voltage in spin. If the washer agitates but will not spin, this could be caused by a failure of several unit components; clutch, drive block, motor, timer, speed cycle switch or wiring harness. If the washer will not agitate or spin, this could be the motor drive coupler that has failed. In order to find the right component to replace, the washer will need to be tested. I would suggest that you have a technician do this.

Read More
Jerome G. - Personal Solutions Manager -
Sears Technician
June 26, 2012
See more answers
Q:

I have a Kenmore washer #11012502100 and it will not advance to the drain/spin cycle. The dial will not advance manually. What could be the problem?

A:

Having an appliance we count on daily to have problems can be really frustrating. While you are waiting on an expert to answer your question, I found a great link that can help you with your problem. I have attache the link below. Hope this helps!

Read More
Dezeray S -
April 03, 2012
A:

Hi Melissa,

Thank you for submitting a question to Manage My Life.

By what you have stated, it sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer to work. If the lid switch is faulty, it will fill and wash but nothing else.

A quick check you can do is to bypass the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced. Here is a video that demonstrates gaining access to and replacing the Lid Switch on a washer that should be similar to yours.

To bypass the lid switch you need to unplug the washer and open the console.

Once you have the console open, locate the connector for the lid switch. Place an insulated jumper wire between the two colored wires (see image below). Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the lid switch bypassed and continue using your washer. This is for testing purposes only.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website; Sears Home Services .

Here is a link that you may use to purchase the lid switch for your Kenmore model number 110.12502100 washer .

I hope this is helpful. Check the things I have covered here and if I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
April 04, 2012
See more answers

Top Parts