Model #110 INGERSOLLRND Air-drive tool

  • Unit
    3 Results
Find part by diagram >

Question and Answers

Q:

What is causing loud banging noise in my Kenmore Model 110.20022013 washer during spin cycle? 11020022013 Kenmore Automatic washer

A:

I have the same machine and mine started doing it last night. Were you able to figure out the problem?

Read More
Allen -
February 02, 2016
A:

I have the same machine and mine started doing it last night. Were you able to figure out the problem?

Read More
Allen -
February 02, 2016
See more answers
Q:

My Kenmore he2 plus washer model #110.47532601 : shows 5 D and than F21 code #110.47532601

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

 

Read More
Joseph P. -
July 20, 2013
A:

Thank you for your question. The 5d code is really SD code. The "SD" error code indicates a Suds Detection. SD is displayed when the machine/motor control analyzes drag on the basket detecting a suds-lock condition. This is generally caused by using the wrong type of detergent or just too much detergent.

The "F21" fault code will display if the drain time exceeds eight minutes. This fault code generally is caused by a restricted drain pump filter or using too much or the wrong kind of detergents.

The first thing to check and clean is the drain pump filter if the drain pump will run. If the drain pump is not running then it may have a jammed or faulty drain pump. I added an image below with instructions on how to access and remove the drain pump filter for cleaning. NOTE: Disconnect the power cord from the power source before removing the lower access panel. Also, remove all the water that you can before removing the drain pump filter or all the water will pour out on the floor. Have a shallow pan and towels handy even though you have removed all the water from the tub there will be water left below the basket.

In order to access the drain pump filter the lower access panel will need to be removed. (See images below.)

  1. Disconnect the power cord from the power source.
  2. Remove the screws (key#21) along the bottom of the lower access panel.
  3. Slide the access panel down and off.
  4. Turn the filter (key#14) counterclockwise to remove the filter assembly.

NOTE: There will be a lot of water left inside the pump so place a shallow pan under the filter before removing. I would also recommend having an old bath towel handy too.

For all your part needs go to www.SearsPartsDirect.com

If you rather haveservice go to www.SearsHomeservices.com

If you have anymore questions reply to this post.

Thank you for choosing Manage My Life.

Read More
dtova00 -
Sears Technician
July 22, 2013
A:

My Kenmore HE2 Plus washer MODEL 11047512602 is throwing an SD and F-21 code. We are using the correct detergent. Sears service guy is scheduled to come, but in 4 weeks. Have cleaned the filter and discharge hose is clear. Is there any other part I can clean or check just to try and get by. Pump is making a vibrating sound.

Read More
Bradley -
January 09, 2016
A:

My front load washer model# 110.47532601 contantly throws an F21 and F33 codes. The drain pump was replaced three years ago. I always clean the pump filter every week, so I leave the front metal cover off for easy access. When I do clean the pump filter , I always check upstream of the pump for socks, etc. The wife knows not to over fill the soap as well.

Read More
k -
February 01, 2016
See more answers
Q:

I have an air compressor model 919.165612, 220 volt. It does not build pressure above 110 psi. There are no leaks, cleaned the filter, it has a new switch. Any ideas?

A:

Your air compressor probably has something broken inside the cylinder. Disconnect the power to the air compressor and remove the plastic cover around the motor and compressor.

Before you take the compressor apart, listen and feel for air leaks. Check to see if air is coming back out of the intake filter. If air is coming back out of the intake filter, something is wrong inside the cylinder.

You can see a parts diagram at [www.searspartsdirect.com]. The parts diagram will help you locate the parts that build air pressure. These are the parts you need to inspect.

Turn the motor shaft by hand and be sure the piston goes up and down.

If the piston is ok remove the 4 screws holding the head on top of the cylinder. Remove the head.

Directly under the head is the pressure plate. The pressure plate has reeds on it that direct the air into the discharge line and keep the air from going back through the intake side of the compressor. Check the reeds for warping or breaking. If the reeds are damaged, you must replace the pressure plate. Make note of how the pressure plate sets and the o-rings that seal around it.

Remove the pressure plate and inspect the plastic sleeve inside the cylinder. Look for scratches or cuts in the sleeve. Make note of the piston and the rubber o-ring around it. If the o-ring is worn or broken the air goes back through the intake filter and no pressure is built. If you have to replace the o-ring, replace the piston and sleeve also.

To replace the o-ring and sleeve, you have to remove the nut that holds the piston to the motor shaft. When you replace the nut you must torque it to 85-90 foot pounds. Torque the head bolts to 7-10 foot pounds.

Read More
Jimmy K -
Sears Technician
August 05, 2009
A:

I have the same compressor. Once over 90 PSI, it slowly leaks air on the right side (where the aluminum right-angled fitting feeds the copper line to the tank). If I push in on the fitting, the sounds slows down. Once below 90, it stops. Anything higher and you can feel air in that vicinity. Not sure how to replace that. Do I need to replace the whole unit (power, pressure switch, fitting, etc.)? First time unit has ever had power (I know, it's old).

Read More
Eric -
January 30, 2016
See more answers