Model #1076 POWERWHEELS/PINES Toy riding

  • Replacement Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

dryer not working/overheating 11085081400 Kenmore Elite Residential dryer

Q:

Sears Craftsman Lawn Tractor Dana Transaxel PN 407136 917.287251

A:

Thanks for the inquiry and for using SearsPartsDirect.com. 
Sorry to hear of the difficulty you're having with the braking on the tractor and missing the spacer on the Dana. 
I don't know if you've tried to order part 407136 from SearsParts and we notified you that it was no longer available, but it shows on the website as 'In Stock.' 
If the part has been discontinued and we no longer have stock, you could take the specs for the spacer and plug them in online to find a replacement if available. 
If that doesn't seem to be doable, you can take the specs to a local machinist and have one made rather inexpensively. 
Those would be the best option I can see for the part. Hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
July 17, 2014
Q:

Oven overheating and door locking

A:

Error codes can be an inconvenience and keep your range from working properly. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with your research while you wait for your expert response.

Read More
Joseph P. -
January 29, 2013
A:

There is a chance that a problem with that door gasket (part 4455380) could be allowing heated air to escape through that area that you are describing. If the control is working properly except when it overheats, then you may be able to fix your problem by replacing that door gasket. Note: The oven has a vent on the top left portion as shown in the second image below. There may be some discoloration in that area around the vent. That is normal and it should not affect the control board.

If replacing that gasket does not fix the problem and you continue to see the E0 F3 code even though the oven temperature sensor circuit is okay, then you will probably need to replace that control board. Be sure that you shut off the house circuit breakers for the oven to completely disconnect electrical power before accessing internal components and replacing parts. The first image below shows how to release that console and access the electronic control board.

You can order parts from this page: Whirlpool Oven Model RBS245PDB12 Parts .

If you need more help, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 30, 2013
A:

Here are the images.

Read More
Lyle W -
Sears Technician
January 30, 2013
A:

Lyle, Thanks for the reply. The brown spot on the gasket is shown on the attached photo. Hoping for a cheaper fix than replacing the control board.

Read More
tom -
January 30, 2013
A:

Hello Tom. Thanks for sending that picture. It does appear that you will need to replace that door gasket. That part should not cost very much. The old gasket can just be pulled off. The new one has metal clips that will push into holes in the frame around the door. I see some dust and lint build-up in those ventilation holes just under the control. I also recommend that you shut off the house circuit breakers for the oven and carefully pull it out of the cabinet. I posted a link for the installation guide below this response that will help you pull the oven out of the cabinet. Remove the top panels (Keys 16 and 18 in the parts image below) and clean that entire control section and fan. Clean the front ventilation slots. This should improve the ventilation air flow through the control area. After replacing the gasket and cleaning the ventilation air path, you may find that the electronic control board will work properly and not overheat. This may fix your problem. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
January 31, 2013
A:

Here is the image.

Read More
Lyle W -
Sears Technician
January 31, 2013
See more answers