Model #1069751722 KENMORE Top-Mount Refrigerator

  • Cabinet
    3 Results
  • Liner
    3 Results
  • Freezer Door
    3 Results
  • Shelves
    3 Results
  • Refrigerator Door
    3 Results
  • Unit Assembly
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

how do I balance the door on the refridgerator? 1069751722 Kenmore Refrigerator

A:

Thank you for choosing SearsPartsDirect.com. I will be more then happy to assist you. Looking at this fridge im not showing That to get the doors balanced on here you need to replace the door hinges to get your door level aging. Hope this information has help you. If you are not comfortable doing this repair you can Click Here to schedule a technician or call toll free 1-800-469-4663. Any further questions or concerns. You will have to post a new question because at this time I can not reply to any comments. Again, Thank you for choosing SearsPartsDirect.com.
 

Read More
Samantha A -
Sears Technician
June 30, 2014
Q:

Freezer does not keep ice from ice maker frozen.

A:

The ice maker is one of the most convenient features features in the refrigerator. It can be very frustrating when the ice is melting. I found some information I am hoping can help you. I am adding the links below to help you with your question while you wait for your expert response. I do hope this will assist you with the refrigerator.

Read More
Marc H -
May 04, 2012
A:

Thank you for your question. I can understand your concern about the ice melting. First, check the temperature in the freezer, it should be 0 to 5 degrees. To check the temperature, place a thermometer between some packages. Air temp is not a good check. If the temperature is too warm, the thermostat may need to be adjusted to a colder setting. If it's still too warm, it could lead to a sealed system problem. A technician would need to make this type of check.

If the temperature is ok, the most likely problem would be the thermostat inside the icemaker staying closed and keeping the mold heater on. This is a heater in the icemaker and if it stays on, it could melt the ice. In this case, the icemaker # 4317943 would need to be replaced. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
May 07, 2012
A:

Actually I watched what happens when I turn the icemaker on. It makes ice but water pours out of the icemaker which is why there is a pool of water that freezes at the bottom of the ice bin. Again, this is a Kenmore model #106.9751722. Any suggestions on how to fix this?

Read More
Karen -
May 07, 2012
A:

Karen, based on this latest information, the most likely problem will be a defective water valve. However, it's possible the icemaker could also be causing this overfill problem. First, try adjusting the water fill using the picture and instructions attached below. If it still overfills, the water valve # 2315576 will need to be replaced. I hope this will help you.

Read More
Scott D -
Sears Technician
May 08, 2012
See more answers
Q:

Kenmore Top-Mount Refrigerator Model: 106.9751722

A:

I think its great that you are wanting to do some repairs on your own. I found a great link that will provide you with a video to help you with your project. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
January 25, 2012
A:

Thank you for your question. I understand your concern about the harness connection. This is a very unusual situation. There should not be anything connected to the icemaker harness. The video you received is very good and shows the harness connection. I suspect this may be a dummy harness. The end of the harness may be capped off or the end needed to connect to the icemaker, may be stuck behind the freezer panel. I suggest following the harness to see where it leads and what the other end looks like. Be sure to disconnect the power first. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further. If you can send a picture it would also be very helpful.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
January 27, 2012
See more answers

Top Parts