Model #10678182891 KENMORE Top-Mount Refrigerator

  • Cabinet
    3 Results
  • Liner
    3 Results
  • Freezer Door
    3 Results
  • Shelf
    3 Results
  • Refrigerator Door
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

ice will not dump from ice maker 106.78182891

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
May 13, 2014
Q:

no water to icemaker Mod # 106.78182891

A:

I know how important it is to have a good working ice maker in the home so that you can enjoy some ice cold beverages. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with your research while you wait for your expert response.

Read More
Joseph P. -
April 13, 2013
A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. This icemaker has some test terminals on the module that may help determine what the problem is. To access the terminals, pull the front cover off of the icemaker. The terminals will be marked (see picture) and using a well insulated jumper, place it between the L - V terminals. Be careful this is a hot (live) check. With the jumper in place, water should flow to the icemaker. If water does flow, the icemaker # 4317943 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # 2315508 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. A technician may be needed to make these checks. I'm listing a site you can access, to have a tech come out. Here is a link for the website:  Sears Home Services. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
April 15, 2013
A:

I had already replaced the icemaker #4317943 with a brand new one. When I used the jumper between L& V. Water did flow into the new maker. Am I to believe that the brand new one was also "broken"?

Read More
Frederick -
April 15, 2013
A:

Frederick, with the jumper in place between L & V, if there is no water flow a voltage check will need to be made at the valve. Disconnect the power and leave the wires connected to the valve. Now, place the meter leads on the terminals and reconnect the power. If there is 120 volts at this check, the valve will need to be replaced. If there is no voltage, then the problem could be with the icemaker or the wiring in between the icemaker and the valve. A technician may be needed to make this type of check. You can call 1-800-469-4663 to schedule a tech to come out. If you would like more assistance, I will be glad to assist you further.

Read More
Scott D -
Sears Technician
April 16, 2013
A:

Well, there is more...the icemaker did begin to make ice but only 6 or 8 pieces. So it is getting H2O but not continuing to work. Is there a way to reset it so it will recycle?

Read More
Frederick -
April 16, 2013
A:

Frederick, this icemaker can be cycled manually by placing the jumper between the T & H terminals. After it starts to cycle, remove the jumper in approx. 12 seconds. Toward the end of the cycle, it will fill with water. If it cycles ok and fills, based on the information listed, this could be a temperature related problem. If the temperature gets above 5 degrees, the icemaker production will slow down and if it gets above 12 degrees, it may not cycle at all. To check the temperature, place a thermometer between some packages. If it is getting too warm, usually adjusting the control to a colder setting will help correct this problem. I hope this will help you.

Read More
Scott D -
Sears Technician
April 17, 2013
See more answers
Q:

My refrigerator is not producing ice fast enough and not enough ice.

A:

I'm sorry to hear that you are having some difficulties with your ice maker. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
Jackie S -
January 09, 2012
A:

I am very sorry that you are having problems with the ice maker. It sounds like it is not releasing enough water into the tray, and the motor may not be cycling properly. Below, I have included images on the cycles for the ice maker and how long they are supposed to last, also on the test points. I would suggest that you use a insulated jumper to manually cycle the ice maker and make sure it is working properly. If this does not work, then you will need to replace the ice maker.

If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
January 11, 2012
See more answers

Top Parts