Model #10676942400 KENMORE Top-Mount Refrigerator

  • Cabinet Parts
    3 Results
  • Liner Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Shelf Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts
    3 Results
  • Water Dispenser Parts, Optional Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Can I disconnect the auto ice maker? Kenmore Top mount

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you.  I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

I’m looking at the information on this Kenmore fridge. I’m showing that with this icemaker you can remove it with no issue. It looks like there are two screws holding this on, and it would leave any kind of holes in it. 

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
Samantha A -
Sears Technician
October 08, 2014
Q:

Replace part 2225521 10676942400

A:

 Hi,

Thanks for contacting  ManageMyLife.  I understand how frustrating it is having trouble with your appliance.

It does not make any logic to have the remove a bracket to remover the filter head.  You may need to block the front of the refrigerator up to get the filter housing off.  The connectors at the water lines are john guest fittings and easy to get to hoses out of. 

Cut and paste this link to the john guest fitting video.   www.youtube.com/watch?v=-Avzf-jsHyM

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
November 01, 2013
Q:

why is my refrigerator icemaker not working

A:

Having one of the options on the refrigerator not working well can be a big inconvenience. I placed a link where an expert specks upon the ice maker. I hope that it helps om regards in what to do next. I also attached the Owner's Manual, it always comes in handy when your needing some specific instructions.

Read More
celene -
December 12, 2010
A:

If my problem is with the mold not heating, how do I repair (part replacement) Thank you

Read More
reedbone -
December 12, 2010
A:

You can try to fix the ice maker by unplugging the refrigerator and completely removing it from the freezer. There are two screws on the top and one on the bottom that mount this ice maker to the side wall. Remove those screws and then unplug the wire harness connection. Take the ice maker out of the freezer and completely thaw the ice mold to that it is completely empty. Take the ice fan off of the front of the ice maker module. Metal clips hold that component in place. You can view the parts list diagram for the ice maker on the Sears PartsDirect website if necessary.

When you remove that ice fan assembly, you will see some gears and labeled test points as shown in the first image below. If you have a volt/ohm meter, you can check the resistance through the test points L and H to test the heater as described in that first image. If the heater is "open" (measures Ol -- open load or infinite resistance) then the ice maker module (part 4317943) will need to be replaced. If the heater is okay, I recommend that you check the motor. If the motor is bad, then the ice maker module will need to be replaced. If the motor and heater are both okay, you could have a problem with the thermostat. Replace the ice maker in the freezer (with the refrigerator) still unplugged. Leave the front cover off of the ice maker so that you can access the test points. Use an insulated jumper wire to manually cycle the ice maker as shown in the third image. If the module works properly when manually cycling it, then you can finish the reassembly and see if the ice maker will eject the frozen cubes and refill. If it does not cycle on its own, then the ice maker module will need to be replaced.

I don't recommend that you replace individual components in the ice maker module. They are available if you want to order the parts that you think that you need.

If you need more help, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 13, 2010
See more answers

Top Parts