Model #10674204400 KENMORE ELITE Top-Mount Refrigerator

  • Cabinet Parts
    3 Results
  • Liner Parts
    3 Results
  • Shelf Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Parts, Optional Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

My refrigerator is not cooling but the freezer is. Seems the ice maker is overfilling. Can you suggest diagnostics please. 10674202400 Kenmore Elite Top mount refrigerator

A:

ops that is the wrong model number. My model number is 10674204400.

Read More
Becky -
September 05, 2013
A:

Thank you for your question. I can see you have been dealing with a couple of issues. First, the ice maker. Check the fill tube to the ice maker tray to see if it is partially frozen.  It may be continuing to drip water into the tray and causing the overfill. After the ice is harvested, observe the ice maker during the fill cycle. It may also be a crack in the fill cup. The best way to check the fill cup will be to pull the ice maker out. First disconnect power to the unit. Now remove the 2 screws on top of the ice maker mold and the one under it. The ice maker will now be free and you can disconnect the wire harness. Now pull the ice maker out and check for an obstruction in the fill cup or a crack. If you can't see anything, pour some water in the cup and watch where the water goes. If a new fill cup is needed, you can order at Sears Parts Direct .  The leak from the ice maker may be the cause of the freezer freezing up, as well. The image below contains the diagnostic for the refrigerator requested. If further help is needed, please reply.  Thank you for using Manage My Life.

Read More
Barbara H. -
Sears Technician
September 07, 2013
See more answers
Q:

freezing fridge

A:

I understand how concerning and frustrating this can be. While you are waiting on an expert to answer your question, I suggest you set service with a Sears technician so they can fix this for you. I have attached the link below. Hope this helps!

Read More
Dezeray -
October 24, 2012
A:

Thank you for your question. I�m sorry you are still having this problem with the fridge section freezing. When the interface was replaced, was the foam gasket also installed next to the air baffle motor? If the gasket was not installed or not installed properly the baffle can freeze and the freezing can continue. I�m attaching the directions to install the gasket. Also if the freezer is getting excessively cold (below zero) it can cause this problem. If it is getting too cold, usually adjusting the control to a warmer setting will correct this. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
October 25, 2012
A:

The foam gasket was already in place when I opened up the baffle, it was intact so I didn't use the new one. I checked and the freezeer was running cold; it had been set at zero but was registering about 7 below. I reset the freezer and fridge as high as possible(5 and 45 degrees) ,removed ice from the air baffle and made sure it was working. When I checked again about 8 hours later I found the freezer at 5 below and the refrigerator continuing to drop - currently at 37, The air baffle is working at present.

Read More
Rich -
October 26, 2012
A:

Rich, if the freezer is getting below zero, it can also cause the fridge section to freeze. Usually, when this problem occurs, adjusting the control to a warmer setting will correct this type of problem. I hope this will help you.

Read More
Scott D -
Sears Technician
October 26, 2012
A:

" I reset the freezer and fridge as high as possible(5 and 45 degrees)" The freezer doesn't go any warmer than 5, the fridge goes no warmer than 45. The settings don't seem to be working.

Read More
Rich -
October 26, 2012
A:

Rich, this could be a defective control or the sensor. Since the control has been replaced and the same problem still occurs, it would lead more to the sensor. To check the sensor, disconnect the harness (see image) and measure the resistance. At 77 degrees, it should have 2700 ohms and at 32 degrees it should have 8750 ohms. If the resistance is more than 5% off, replace the thermistor # 2188820. Be sure to disconnect the power before removing the control. I hope this will help you.

Read More
Scott D -
Sears Technician
October 29, 2012
See more answers
Q:

Freezing fridge

A:

I understand that your refrigerator is freezing up. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Alina -
October 05, 2012
A:

Thank you for submitting your question. If the refrigerator section is too cold it will be because the evaporator air is bypassing the rear diffuser through the opening next to the baffle motor. You'll need to replace the user interface board and install a square foam gasket next to the air baffle motor. The user interface kit part number 2304085. You can order parts from our Sears Parts Direct web site. The image below will assist you in the replacement of the baffle gasket. I hope this information helps. Please reply back to this thread if you require further assistance with this repair. If you do not feel comfortable performing test or repairing this problem yourself, I recommend scheduling for service. You can schedule for service online with our Sears Home Services team. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
October 06, 2012
See more answers

Top Parts