Model #10670204990 KENMORE Top-Mount Refrigerator

  • Cabinet
    3 Results
  • Liner
    3 Results
  • Shelf
    3 Results
  • Refrigerator Door
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
  • Freezer Door
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

cu.ft. refer cu.ft. freezer 10670204990 Kenmore Top mount refrigerator

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Marc -
April 10, 2013
A:

Thanks for contacting ManageMyLife.com. I understand how important it is to have information to ensure you purchase the right refrigerator. Refrigerator 10670204990 is 21.6 cubic feet but would most likely classified as a 22 cubic foot model for sales.

You may click here to look at newer model refrigerators on Sears.com.

Please feel free to let me know if you need further assistance.

Thank you for using ManageMyLife.com.

Read More
Jonathan B -
Sears Technician
April 11, 2013
See more answers
Q:

Kenmore 106.70204990 won't restart after cooling

A:

I know how important it is to have a good working refrigerator in the home so that you can keep your food nice and fresh. While you are waiting for an expert answer, I did manage to find a great link that provides tips for what may be causing your problem. I hope my link is useful.

Read More
Joseph P. -
January 17, 2011
A:

I think the thermostat in the refrigerator has failed. You can go to www.partsdirect.com?sid=MMLxexpertxmerch and see a parts diagram for your refrigerator. Select the "cabinet" page. The thermostat is item 13. The thermostat is what you turn when you turn the knob off and on.

The part number for the thermostat is 2302286, and the price is $29.62.

Read More
Jimmy K -
Sears Technician
January 18, 2011
A:

thanks Jimmy K for your input. I ordered the part and I'm going to put it in myself--anything tricky with this installation?

Read More
Tony -
January 19, 2011
A:

You should look at the parts diagram at www.partsdirect.com?sid=MMLxexpertxmerch]. The parts diagram shows the parts that are located in the control panel. This will show you what you have to remove to access the thermostat. Be sure you route and locate the sensing tube the same as the old one was routed and located. Good luck. Be sure to disconnect power to the refrigerator before removing any panels. The wires in the control panel are live.

Read More
Jimmy K -
Sears Technician
January 20, 2011
See more answers
Q:

model 10670204990 refrigerator ice maker problem. Ice hopper solid block, ice in bottom of freezer, water on floor.

A:

I can see how upsetting finding all of this would be and it is confusing knowing what to check. I found a question from a previous expert post that although the question is a bit different, the results are the same that you have for your fridge. The model is the same as yours, so I attached the link below. Hope this helps stop the water.

Read More
Barbara H. -
January 16, 2011
A:

Hi, Thanks for your suggestion. I'd actually considered, and then eliminated, the issue of a plugged drain. The drain was clear when I checked it this morning. While the unit had sat overnight unplugged and with the doors open, I still had considerable ice in the bottom of the freezer compartment. From what I can tell though, the drain tube was clear. I have thoroughly defrosted and dried ( with a hair dryer) the freezing compartment, removed, dried and reinstalled the ice maker,reassembled everything and started the unit back up. I'm waiting for it to chill enough that the ice maker will cycle. Given the fact that there was a block of ice in the collection hopper, I'm suspecting an issue with either the ice maker or the water valve.

Read More
garyneilholt -
January 16, 2011
A:

I suspect the water valve had to stick open to cause that much water inside the freezer and refrigerator.

I would place a pan under the icemaker to catch the water that overflows, and manually turn the fill valve on for 1-2 seconds eight or ten times. I am sending you a diagram showing how to insert a jumper wire into the test terminals of the icemaker to make the water valve dispense water.

Make a jumper wire from 14 gauge insulated wire about 3-4 inches long. Strip about 1/2 inch of insulation off each end. Remove the front cover of the icemaker and hold the door switch closed while you run the test.

Be careful to only touch the insulated part of the jumper wire and insert the ends into terminals L and V on the icemaker. I am sending you an image showing the test points. The water should turn off instantly when you remove the jumper. If the valve is sticking you will probably see the water turn off slowly. If this happens you should replace the water valve. You can order a water valve at [www.partsdirect.com?sid=MMLxexpertxmerch]. The part number of the water valve is 2315576 and the cost is $40.29.

Read More
Jimmy K -
Sears Technician
January 17, 2011
See more answers

Top Parts