Model #10670203991 KENMORE Top-Mount Refrigerator

  • Cabinet
    3 Results
  • Liner
    3 Results
  • Shelf
    3 Results
  • Refrigerator Door
    3 Results
  • Unit
    3 Results
  • Ice Maker
    3 Results
  • Freezer Door
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I have a Kenmore coldspot #106.70203991. Behind the light bulb there's a vent on the top. Water is dripping down from there. How do I fix this and how much would it cost to repair.

A:

Water dripping in the refrigerator can be a hassle and cause some water damage. I am adding a link below to help you wit your question while you wait for your expert response.

Read More
Joseph P. -
January 30, 2012
A:

Thanks for contacting ManageMyLife.com. I understand how frustrating and messy it is to have a refrigerator drip water inside. We are here to help. Water will leak into the refrigerator when the drain system freezes up. Every time the unit goes into a defrost cycle, water will run down into the refrigerator, instead of down the drain. To correct the problem the first thing you need to do is unplug the refrigerator for safety. All the food along with the icemaker has to be removed. With the food and icemaker out of the way the back panel can be removed.

With the panel removed, you will see the evaporator coil and directly under the coil is the drain trough (pan). The trough will probably be full of ice that will need to be removed. A hair dryer works well for this. Just be careful not to get it too hot. With the ice out of the trough, you will be able to see the drain hole, which will be plugged with ice. Use hot water to clear the drain hole. Keep working the hot water into the hole and wiping the excess water. This can take quite awhile, depending on how deep the ice is. This will need to be done until you get a good water flow down to the bottom drain pan. With the drain system clear, water should stop leaking in the refrigerator.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. You may visit SearsHomeServices.com and click on the red Start now button. The web site listed in the link above will tell you how much it cost for a Sears Technician co come to your house. Please feel free to let me know if you need further assistance we are here to help. Thank you for using ManageMyLife.com.

Read More
Jonathan B -
Sears Technician
February 01, 2012
See more answers
Q:

Can I get an overload switch for a Kenmore model 106.70203991 refrigerator?

A:

For any parts you can view a complete breakdown of your refrigerator at the following site: Sears PartsDirect .

The part number for the overload is 4387913 and is available from the same site.

I hope this information is helpful to you but submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
January 13, 2010
Q:

What part is needed for my icemaker?

A:

The problem could be with the icemaker itself or the water valve. There are some test terminals on the icemaker module (I'm sending a picture), that can help determine the problem. To access the module, pull the front cover off of the icemaker. Place a well insulated jumper between L-V, to check for water flow. Be careful this is a hot (live) check. If water does flow, the water valve is ok. If no water flows, the valve will probably need to be replaced. You can also place the jumper between T-H and the icemaker should start into a cycle. If it does remove the jumper after a few seconds. If it cycles and fills, it indicates the icemaker is not cycling on its own and will need to be replaced.

Read More
Scott D -
Sears Technician
April 29, 2009

Top Parts