Model #10670194001 KENMORE Top-Mount Refrigerator

  • Cabinet
    3 Results
  • Liner
    3 Results
  • Freezer Door
    3 Results
  • Shelf
    3 Results
  • Refrigeator Door
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Freezer bulb shield removal Mod. 106.7019

A:

If the old bulb works and the new bulb doesn't, I'm wondering if it isn't the bulb itself. I found a link that is similar to your model number that provides instructions for replacement. If this doesn't help, you will receive a response from our expert team within a day or two. I do hope this helps you and have a pleasant Sunday morning.

Read More
Henry -
September 23, 2012
A:

Henry, Thanks but I didn't explain situation clearly. Both bulbs (old and new) work fine in different fixture. Neither works in freezer socket. Would like to look inside freezer socket but can't figure out how to remove shield. There is a hole on bottom front but goes up to a "nub"...i.e. no screw head or nut head. Pix on link sent are very different from 106.7019 freezer bulb shield.

Read More
alfred532 -
September 24, 2012
A:

Thank you for your question. I understand your concern about the freezer light. The model listed is not complete and I'm showing a few top mount models with it. If this is correct, I'm attaching a picture with instructions for the light shield for the models shown. Before removing the light shield, I suggest checking the switch. First disconnect power from the unit. Pry the switch out with a small screwdriver and connect the wires together. Now, reconnect the power and if the light works, the switch # 1118894 will need to be replaced. I hope this will help you. If you would like more assistance, reply to this tread and please include the complete model number and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
September 25, 2012
A:

Scott, thanks for replying. Full model no. is 106.70194001. Couldn't find the picture you attached. but did pry the switch out. Wasn't able to connect the wires but will order a new switch anyway as it is likely the problem. How do I order new switch? and is switch # number above still correct given full model number?

Read More
alfred532 -
September 25, 2012
A:

Alfred, thank you for the model number. Yes, the switch listed above is also correct for this model. It's available at Kenmore refrigerator parts. I hope this helps you.

Read More
Scott D -
Sears Technician
September 26, 2012
A:

Scott D. Ordered and received freezer light switch. If wires were half inch longer, would be easy to install. Now back to needing to know how to remove shield so I can snap in new switch.

Read More
alfred532 -
October 14, 2012
A:

Alfred, I'm attaching some pictures with instructions to access the housing and remove the shield. I hope this will help you.

Read More
Scott D -
Sears Technician
October 15, 2012
See more answers
Q:

troubleshoot top mount refrigerator icemaker

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina F. -
October 18, 2011
A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. This icemaker has some test terminals on the module that may help determine what the problem is. To access the terminals, pull the front cover off of the icemaker. The terminals will be marked (see picture) and using a well insulated jumper, place it between the L - V terminals. Be careful this is a hot (live) check. With the jumper in place, water should flow to the icemaker. If water does flow, the icemaker will need to be replaced. If no water flows but you can hear a humming noise, the water valve # 2315576 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. A technician may be needed to make these checks. I'm listing a site you can access, to have a tech come out. Here is a link for the website: Sears Home Services . If you would like more assistance, reply to this thread and I will be glad to assist you further. Thank you for using Manage My Life.

Read More
Scott D -
Sears Technician
October 19, 2011
A:

Thanks Scott - I will try the jumper. I can check other voltages if I know what to look for. I am a mechanic and do electrical wiring and repairs on computers/electronics, houses and equipment.

Read More
Tom -
October 19, 2011
A:

If the icemaker does nothing, place the jumper between the T & H terminals and then check for 120 volts between the L & N terminals. If the voltage is there, the icemaker will need to be replaced. Be very careful when making this voltage check. I hope this will help you.

Read More
Scott D -
Sears Technician
October 20, 2011
See more answers

Top Parts