Model #10658029801 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Why is my icemaker not working on my side by side refrigerator, model 106.58029801

A:

I can understand the inconvenience that you might be going throw because of the ice maker not working correctly. Providing more detailed information will be great if you can add it to this thread. In the mean while i provided the owner's manual that also gives you useful information upon the ice maker, good luck.

Read More
celene -
October 19, 2010
A:

I'm sorry you are having this problem. The information you have received is good, about checking the owner's manual. However, I hope the following information about this icemaker, will help you.

The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it�s normal. Now disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I�m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L � V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # 4389177 will need to be replaced. If nothing at all happens, some voltage checks will need to be made.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be needed.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
October 21, 2010
See more answers
Q:

kenmore ice maker 105.58029801 is not dispensing

A:

I understand your ice maker is not dispensing properly but it is making ice fine. I found a question in Manage My Life under the Answers button that was similar to the one you asked. This question should be very helpful to you, while your waiting on an expert answer. I attached the link below, I hope this helps!!!!!!!!

Read More
Raquel F -
August 10, 2010
A:

Thank you for your question.

  • First make sure the bucket is docking completely onto the drive coupling. If the bucket is not sitting completely down, reach into the bucket and turn the arm until it docks with the coupling.

* If that is docking ok, it sounds like the drive coupling on your dispenser is broken.

  • You can check this by removing the ice bucket from the door and looking at the docking point where the two couplings meet.

  • You should be able to operate the arm in the bucket and look at the bottom side of the bucket to see the cogs. If the cogs on the bucket are ok, then check the drive coupling on the motor where the bucket docks.

  • If you press and hold the door light switch and reach around the door with your other hand and press the ice lever in the dispenser you should be able to see the coupling rotate. If it does not and all you hear is the motor running the drive coupling will need to be replaced.

  • To check to the drive motor coupling remove the two screws that hold the top support for the drive coupling on the freezer door. Keep track of the parts in their proper order to replace correctly.

  • Remove the housing and pull out the coupling and examine for damage.

  • If the drive coupling is broken here is the part number for the drive coupling. I will also include the drive shaft part number.

  • Drive shaft 2188916
  • Drive coupling 2315559

You can order these parts from Sears Parts Direct .

Read More
Sam A -
Sears Technician
August 12, 2010
See more answers
Q:

How can I keep the door water line from freezing?

A:

Refer to previous answer: No, this is not a common problem but it can happen. When this problem does occur, the main reason is because of the temperature being too cold (below zero). Usually, just adjusting the temperature as you have done, to a warmer setting will correct this. To check the temperature, place a thermometer between some packages, air temperature is not a good check. If you need more assistance, please resubmit your question with more details.

Read More
Scott D -
Sears Technician
January 21, 2010

Top Parts